Uttar Pradesh Rajkiya Nirman Nigam Limited - Madhya Pradesh

39965694 erection ( work contract ) items for thdc works singrauli ( m.p. ) 2 h beam 13 meter 152 x 152 mm 37.1 kg / meter 3 33 kv v cross arm 1.5 mtr ( 5ft ) centre made from 75x75x6mm angle 4 back clamp for h beam pole of 65x8mm ms flat 5 33 kv top clamps 75x75x6mm angle type 6 earthing coil of 115 turns of 50 mm.dia and 2.5 mtr lead of 4.0 mm g.i wire 7 33 kv, 10 kn pin composite polymer insulator 8 aaac dog conductor 0.10 sq. inch ( 100 sq.mm. al.eq. ) 9 jointing sleeves ( aluminium ) for dog conductor 10 stay set 20 mm complete 11 h.beam clamps 65x8mm flat 12 concreting ( 1:3:6 ) of h beam @ 0.65 cmt.per pole ( base pedding + muffing ) 13 concreting ( 1:3:6 ) of stay @ 0.3 cmt. per stay ( 20mm ) 14 red oxide paint 15 aluminum paint 16 anti climbing device ( barbed wire 3.5 kg ) gs 2.5 mm dia ( 12 swg ) 17 danger board enameled 33 kv 18 dc.cross arms 8` ( 2.4 meter ) centre to centre 100x50x6 mm channel 19 33 kv , 45 kn disc polymer long rod type t&c insulator 20 bracing set for 8 feet ( 2.45 mtr ) centre dp angle 21 bracing set for 5 feet ( 1.5 mtr ) centre dp angle 22 33 kv suspension clamps with attachment for a.b cable 23 33 kv tension clamps ( dead end ) with attachment for a.b cable 24 33 kv arial bunch cable 95 sqmm 25 cable straight through joint kits suitable for 95 sq.mm. 26 cable end termination kits suitable for 95 sqmm 27 xlpe cable 33 kv armoured 3x300 sqmm 28 outdoor / indoor end termination kit ( 3x300 sqmm for 2 way rmu ) 29 33 kv bridling cross arms 75x75x6mm 30 33 kv guarding channel 75x40x6 mm 31 fixing of 25 mtr high mast shaft of approved make with rising system hot dip glavanized inside & out side dip, heaving pole sheet thickness 4 mm. top dia minium 150 mm, bottom dia 460 mm base plate 32 mm thick suitable for wind velocity as per is 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 8 to 14 luminaries & its control gear boxes 1.5 hp power tool moter, 3 point suspension system with steel wire rope 8 mm dia, double drum winch, including making suitable foundation as per manufature drawing / site reuiment along with 08 nos foundation bolts nuts, washers, anchor plates etc complete in all respect ( including erection cost ) . 32 itc of outdoor type feeder pillar ( powder coated metal sheet outer door thickness 2mm, inner door thicness 1.6 mm, each door shall be provided with 2 numbers industrial locks ) , for service connection in underground lt line incoming al. ec grade bus bar for lilo 300 amp. 30x10 mm. mccb: 1 no. 125 amp, 18 ka b.c at 415 volts tp mccb with copper neutral link, busbar:1 set 200 amp , aluminium busbar, outgoing mccb current rating: 32 amp, 10 ka b.c., , 30 nos. spn . is 5039, is 13947, iec 65029, is 2147 and relevant is standards 33 fixing of 350 watt flood light ( long range ) 34 fixing of 350 watt flood light ( wide spread ) 35 fixing of 4c x 25 sqmm aluminium armoured cable xlpe insulated 36 laying of one number armoured / unarmoured power cable 1.1kv grade of size not exceeding 25 sq. mm direct in ground including excavation in all soil / murrum / soft rock, sand cushioning, protective covering and refilling the pit etc. as required 37 supplying and making end termination with brass compression gland and aluminium lugs for following size of pvc insulated and pvc sheathed / xlpe aluminium conductor cable of 1.1kv grade as required. ( 4c x 25 sqmm ) 28 mm 38 fixing of mccb 100 amp ( 4 pole ) with frame complete 39 fixing of 5 core x 6 sq.mm trailing copper cable 40 fixing of xlpe insulated frls heavy duty power cable conforming is 7098 ( part 1 ) 1988, 1100 volt grade, 4 core 2.5 sq. mm isi marked with copper stranded / solid conductor. 41 fixing of xlpe insulated frls heavy duty power cable conforming is 7098 ( part 1 ) 1988, 1100 volt grade, 2 core 2.5 sq. mm core isi marked with copper stranded / solid conductor. 42 earthing with g.i. earth plate 600mmx600mmx3mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 mt. long etc with charcoal / coke and salt as required. 43 sub station installation, testing & commissioning of out door type 10 mva power transformer oftc with on load tap changer is 2026, iec296, and any other relevant is including loading, unloading, local carriage & erection of the same on plinth & making all necessary connection etc. complete in all respects as per specification. cable termination box with disconnecting facility for 33 kv xlpe cable at 33 kv side. cable termination box with disconnecting facility for 11 kv xlpe cable at 11 kv side. on load tap changer+ / 7.5@2.5%, bi directional roller, conservator with drain valve, earthing ferminals, double diaphragm explosion vent, radiator with top & bottom shut off valve, first filling of oil including make up fill, silica gel breather with oil seal, rating and diagram plate, air release plug, buchholz relay with shut off valve, winding temperature indicator ( wti ) , oil temperature indicator ( oti ) , megenatic oil level guage, pressure relief device, marshalling box. no load losses 8kw, load losses 50kw, toleronce as per i.s. code 44 installation, testing & commissioning of 33kv vcb panel 1250amp , copper bus bar , inbuild c.t & p.t, protection relays , digital instruments like ameter , voltmeter etc. incomer 02nos bus coupler 01 no outgoing 02 nos 45 installation, testing & commissioning of 11kv vcb panel 1250amp , copper bus bar , inbuild c.t & p.t, protection relays , digital instruments like ameter , voltmeter etc. incomer 02nos bus coupler 01 no outgoing 08 nos 46 laying of one number xlpe power cable of 33 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 47 upto 120 sq. mm 48 supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, xlpe aluminium conductor cable of 33 kv grade as required: 49 120 sq. mm 50 supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, xlpe aluminium conductor cable of 33 kv grade as required: 51 120 sq. mm 52 laying of one number pvc insulated and pvc sheathed i xlpe power cable of 11 kv grade of following size direct in ground including excavation, sand cushioning, protective covering and refillinq the trench etc as required. 53 above 120 sq. mm and upto 400 sq. mm 54 supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, xlpe aluminium conductor cable of 11 kv grade as required: 55 300 sq. mm 56 supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, xlpe aluminium conductor cable of 11 kv grade as required: 57 300 sq. mm 58 providing, laying and fixing following dia rcc pipe np2 class ( light duty ) in ground complete with rcc collars, jointing with cement mortar 1 :2 ( 1 cement : 2 fine sand ) including trenching ( 75 cm deep ) and refillinq etc as required. 59 300 mm dia 60 laying of aluminium conductor pvc insulated armoured served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. on surface the cable run shall be fixed on m.s. clamps etc. of suitable size or as directed by the engineer incharge, complete in all respect. the armouring of the cable shall be properly connected with the earth conductor by clamps etc 61 50 sq. mm 3 1 / 2 core 62 150 sq. mm 3 1 / 2 core 63 supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of pvc insulated and pvc sheathed i xlpe aluminium conductor cable of 1.1 kv grade as required. 64 31 / 2x50sq. mm 65 31 / 2x150sq. mm 66 erection, testing and commissioning of 48 v dc, 200 ah, vrla battery consisting 24 no cell of 2 volt each. including battery charging arrangement with all ac / dc ameter and voltmeter meters. 67 erection, testing and commissioning of direct curent distribution board ( dcdb ) 24 volts indoor floor / wall mounted comprising of 1 no. 2p / 100a dc mccb 5a switch fuse unit as incommer and 8 no. 2p / 40a mccb 5a switch fuse units for each individual outgoing circuit of indoor control panels, indoor / outdoor vcb panels, 1 no. 2p / 40a mccb 5a switch for control room emergency dc lighting including 20% as spare. each incoming & outgoing shall have indicating lamp, 68 erection, testing and commissioning of acdb 415 v, along with three phase neutral voltmeter, three phase ammeter and selector switches, 1no. 200 amps tpn switch fuse unit as incomer, 1no. 63 amp. tpn mccb switches as outgoing feeders & 2no. 32 amp. mccb as outgoing for yard and control room lightining and 6 no. 16 no. mccb for control panels, each incoming & outgoing shall have indicating lamp. including 20% spare 69 installation, testing & commissioning of lattice structure 70 fixing of 33 kv, isolator 800 amp. ( turn and twist type ) 71 equipments installation, testing & commissioning of bis certified energy efficiency level iii ( old ) / level ii ( new ) convential 11 / 0.433kv, 100 kva distribution transformer 72 installation, testing & commissioning of marshelling box with 10 no. connectors 73 erection, testing and commissioning of lt distribution box with 1.2 mm thick ms powder coated sheet, 200 a mcb on incoming & 6 no. 125 a hrc fuse base including 100 a hrc fuse , for 100 kva transformer made of smc 74 fixing of transformer mounting channel ( 100x50x6mm ) 75 fixing of copper control cable 2 core. 2.5 sq.mm. ( unarmoured ) 76 fixing of copper control cable 4 core. 2.5 sq.mm. ( unarmoured ) 77 fixing of copper control cable 8 core. 2.5 sq.mm. ( unarmoured ) 78 fixing of copper control cable 12 core. 2.5 sq.mm. ( unarmoured ) 79 fixing of bi metallic clamp for power transformer of brass flat 50x50x10mm 80 for gantry structure ( 33kv ) installation, testing & commissioning of h beams 152 x 152 mm., 37.1 kg. / mtr 13 mtr. long = 482.3 kgx 81 installation, testing & commissioning of d.c. channel 4.8 mtr. centre 100x50x6mm for 33kv gantry structure ( each weight 99.90 kg ) 82 installation, testing & commissioning of back clamp suitable for h beam ( ms flat 65x8 mm ) each weight 1.92 kg 83 installation, testing & commissioning of 33 kv top clamps 75x75x6 mm angle ( each weight 3.58 kg ) 84 installation, testing & commissioning of earthing coil ( coil of 115 turns of 50 mm.dia. and 2.5 mtrs. lead of 4.0 mm. g.i wire ) 85 installation, testing & commissioning of aaac dog conductor 0.10 sq. inch ( 100 sq.mm. al.eq. ) 86 suppy and erection of single piece nonlinear resistor type lightning arrestor suitable for3wire 33kv overhead lines with rated voltage 30kv ( rms ) with a nominal discharge current rating of 10ka ( station class ) and complete with galvanized clamping arrangement , g.i bolts , nuts, washers etc. as required. 87 suppy and erection of 33kv pin insulator complete with large steel head g.i. pin , nuts, washers etc as required. 88 stone block / pre cast block for base pedding 450x450x75 mm 89 concreting ( 1:3:6 ) 0.36 cmt for [ h beam 7 m, 9 m & rsj 9.3 m, pcc pole dp / tp / 4p / 6p of 140 kg. 8 m 200 kg. 9 m 280 kg. 9 m ] , 0.56 cmt for 11 m, 0.60 cmt for 13 m, 0.67 cmt for 15 m per pole including muffing with pole pit digging by hydra m / c. 90 clamp suitable for 152 x 152 mm., 37.1 kg. / mtr 13 mtr. long h beam ( each weight 3.2 kg ) 91 11kv outgoing lines ( 06 nos bays ) installation, testing & commissioning of 200 kg., 9.0 mtrs. long pcc poles 92 installation, testing & commissioning of d.c. channel 4.8 mtr centre 100x50x6mm for 11kv ( each weight 99.90 kg ) 93 installation, testing & commissioning of back clamp suitable for 280 kg pcc pole ( ms flat 65x8 mm ) each wt 1.92 kg 94 installation, testing & commissioning of 11 kv top clamps angle type 65x65x6 mm 95 suppy and erection of three piece nonlinear resistor type lightning arrestor suitable for 3wire 11kv overhead lines with rated voltage 9kv ( rms ) with a nominal discharge current rating of 5ka ( station class ) and complete with galvanized clamping arrangement , g.i bolts , nuts, washers etc. as required. 96 suppy and erection of 11kv pin insulator complete with large steel head g.i. pin , nuts, washers etc as required. 97 installation, testing & commissioning of mesh earthing for new 33 / 11kv sub station inblack cotton soil as per schedule g 3.1 98 installation, testing & commissioning 1500 kvar auto switch, 11 kv capacitor bank complete with individual fuses , interconnection , mounting racks, external fuses, mounting arrangement, bas insulator and accessories with earthing and marshelling box 99 installation, testing & commissioning of earthing of capacitor bank as per schedule g 6.1 ( for black cotton soil ) 100 installation, testing & commissioning of earthing with copper earth plate 600mmx600mmx3mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 mt. long etc with charcoal / coke and salt as required. 101 laying of 32mm x 6mm copper strip from earth electrode directly in the ground as required complete in all respect. 102 miscellaneous items ( i ) safety helmets 103 ( ii ) tong tester digital ( 1000a, 500v ) with associates accessory 104 ( iii ) chain pully block 3ton with 15 metre chain. 105 ( iv ) wall mounting type holder for hydrometer 106 megger anolog 1000 v 107 megger anolog 5000 v. 108 ( vii ) battery hydrometer 109 ( viii ) rubber hand gloves for 15kv ( seamless ) 110 ( ix ) transformer oil dielectric breakdown test kit 111 fixing of fire bucket, round bottom made of g.i. sheet 9 11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of engineer in charge. 112 fixing of shock treatment chart ( prescribed under i.e. rules ) duly framed with glass and supported from back with hard board or soft board with supply of all material labour t&p for proper completion of work 113 fixing of fire extinguisher, abc type 9.00 kg. capacity ( isi marked is : 15683 & tac approved ) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. 114 fixing of c02 type fire extinguisher 6.5 kg. capacity ( isi marked is : 2878 & tac approved ) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. 115 laying of 11kv 1800mm x 900mm x 12mm thick chequered rubbbber matting of tested quality. 116 earth resistance tester ( 20 / 200 / 2000ohms ) digital 117 filter machine 250gph ( transformer oil filtration purpose ) 118 fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch tso 100 series with contactors, hrc fuses, isolating switch metering instrument & instrument box with cts etc. in case of tpn, complete in all respect. auto / mannual selector switch 24 hour programmable timer. 40a tpn 119 fixing of mccb ) suitable for 3 phase & n, 4 pole, ac supply with micro processor release ( mccb, 25ka, 40 & 100 amps, 4p ) 120 fixing of steel enclosure, neutral bar suitable for mcb / rcbos / mccb ( 63a / 100a, 3p / 4p enclosure ) 121 laying of 4 x 10sq.mm aluminium cable a2xfy type. 122 cables & wirings wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface i recessed steel conduit, with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm frls pvc insulated copper conductor single core cable etc. as required 123 group c 124 wiring for twin control light point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface i recessed steel conduit, 2 way modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc .as required. 125 wiring for light / power plug with 2x4 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit alongwith 1 no. 4 sq. mm frls pvc insulated copper conductor single core cable for loop earthing as required. 126 wiring for light / power plug with 4x4 sq. mm frls pvc insulated copper conductor single core cable in surface / recessed steel conduit alongwith 2 nos. 4 sq. mm frls pvc insulated copper conductor single core cable for loop earthing as required. 127 wiring for circuiv submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface / recessed steel conduit as required. 128 2 x 1.5 sq. mm + 1 x 1.5 sq. mm earth wire 129 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire 130 2 x 4 sq. mm + 1 x 4 sq. mm earth wire 131 2 x 6 sq. mm + 1 x 6 sq. mm earth wire 132 4 x 10 sq. mm+ 2 x 6 sq. mm earth wire 133 supplying and drawing following pair 0.5 mm dia frls pvc insulated annealed copper conductor, unarmored telephone cable in the existing surface / recessed steel / pvc conduit as required. 134 2 pair 135 supplying and drawing co axial tv cable rg 6 grade, 0.7 mm solid copper conductor pe insulated, shielded with fine tinned copper braid and protected with pvc sheath in the existing surface / recessed steel / pvc conduit as required 136 supplying and fixing of following sizes of steel conduit along with accessories in surface / recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 137 20 mm 138 25 mm 139 40 mm 140 supplying and fixing metal box of following sizes ( nominal size ) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 141 75 mm x 75 mm x 60 mm deep 142 100mmx100 mm x 60 mm deep 143 150 mm x 75 mm x 60 mm deep 144 150mmx150 mm x 60 mm deep 145 supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 146 5 / 6 a switch 147 2 way 5 / 6 a switch 148 15 / 16 a switch 149 3 pin 5 / 6 a socket outlet 150 6 pin 15 / 16 a socket outlet 151 telephone socket outlet 152 tv antenna socket outlet 153 bell push 154 supplying, erection and testing of approved make electric ceiling fan of double ball bearing complete with standard down rod, canopy, hanging shackle, aluminium blades, without regulator, a.c. 230 250 volts including connections with all necessary material complete of approved as required confirming to is :374 / 2019 with upto date amendments. ( 1400 mm sweep ) 155 supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 156 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. 157 supplying and fixing call bell / buzzer suitable for single phase, 230 v, complete as required. 158 numbering of ceiling fan / exhaust fan / fluorescent fittings as required. 159 installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required 160 upto 450 mm sweep 161 supplying and drawing of utp 4 pair cat 6 lan cable in the existing surface / recessed steel / pvc conduit as required 162 2 run of cable 163 supplying and fixing following way, horizontal type three pole and neutral, sheet steel, mcb distribution board, 415 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / lsolator ) 164 6 way ( 4 + 18 ) , double door 165 8 way ( 4 + 24 ) , double door 166 supplying and fixing 5 a to 32 a rating, 240 / 415 v, 10 ka, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioninq etc. as required 167 single pole 168 supplying and fixing single pole blanking plate in the existing mcb db complete etc. as required. 169 supplying and fixing following rating, four pole, 415 v, isolator in the existing mcb db complete with connections, testing and commissioninq etc. as required. 170 63a 171 100a 172 providing and fixing h.t. danger notice plate of 250 mm x 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. 173 supplying and installing following size of perforated painted with powder coating m.s. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as required. 174 150 mm width x 50 mm depth x 1.6 mm thickness 175 200 mm width x 50 mm depth x 1.6 mm thickness 176 supplying and installing following size of perforated painted with powder coating m.s. cable trays bends with perforation not more than 17.5%, , joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as reauired. 177 150 mm width x 50 mm depth x 1.6 mm thickness 178 200 mm width x 50 mm depth x 1.6 mm thickness 179 supplying and installing following size of perforated painted with powder coating m.s. cable trays tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with m.s. suspenders including bolts & nuts, painting suspenders etc as reauired 180 150 mm width x 50 mm depth x 1.6 mm thickness 181 225 mm width x 50 mm depth x 1.6 mm thickness 182 supplying and fixing cable route marker with 10 cm x 10 cm x 5 mm thick g.i. plate with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required. 183 fixing of 7 mtr gi octagonal pole of approved make ( top dia 70mm, bottom dia 130mm and base plate 12mm thik ) having 3mm thikness with single arm bracket ( 1 mtr length ) on rcc foundation including the cost of foundation, foundation bolts, excavation & back filling and required t&p completee in all respect 184 fixing of led street light fitting having die cast aluminium body and diffuser with driver set suitable for 140 to 150 watt. confirming to ip 66 protection complete in all respects cat aaa 185 surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. all kinds of soil 186 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer in charge. all kinds of soil 187 excavating, supplying and filling of local earth ( including royalty ) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 188 supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete 189 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level :1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 40 mm nominal size ) 190 diluting and injecting chemical emulsion for post constructional anti termite treatment ( excluding the cost of chemical emulsion ) :treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 ( 1 cement : 2 coarse sand ) to match the existing floor: with chlorpyriphos / lindane e.c. 20% with 1% concentration 191 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mm nominal size ) . & centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform 192 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mm nominal size ) . & centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform 193 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mm nominal size ) . & centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform 194 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level : 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mm nominal size ) 195 reinforced cement concrete work in walls ( any thickness ) , including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mm nominal size ) 196 centering and shuttering including strutting, propping etc. and removal of form for :lintels, beams, plinth beams, girders, bressumers and cantilevers 197 centering and shuttering including strutting, propping etc. and removal of form for :suspended floors, roofs, landings, balconies and access platform 198 centering and shuttering including strutting, propping etc. and removal of form for :foundations, footings, bases of columns, etc. for mass concrete 199 centering and shuttering including strutting, propping etc. and removal of form for :columns, pillars, piers, butments, posts and struts 200 brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:cement mortar 1:6 ( 1 cement : 6 coarse sand ) . 201 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1:6 ( 1 cement : 6 coarse sand ) 202 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in cement mortar 1:4 ( 1 cement : 4 coarse sand ) 203 providing & applying a coat of residual petroleum bitumen of grade of vg 10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 204 providing and fixing isi marked flush door shutters conforming to is : 2202 ( part i ) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including isi marked stainless steel butt hinges with necessary screws 205 providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size 206 providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete.fixed to steel windows by welding 207 providing and fixing factory made isi marked steel glazed doors, windows and ventilators, side / top / centre hung, with beading and all members such as f7d, f4b, k11 b and k12 b etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, ( sectional weight of only steel members shall be measured for payment ) . fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) 208 providing and fixing t iron frames for doors, windows and ventilators of mild steel tee sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of c.c. 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) . 209 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. mild steel and medium tensile steel bars 210 fixing of steel or wooden chaukhats in position. 211 ( a ) door chaukhats 212 ( b ) window chaukhats 213 ( b ) ventilator chaukhats 214 15 mm cement plaster on plinth side of single or half brick wall of mix : 1:4 ( 1 cement: 4 coarse sand ) 215 12 mm cement plaster of mix :1:6 ( 1 cement: 6 coarse sand ) 216 15 mm cement plaster on rough side of single or half brick wall of mix : ( 1 cement: 6 coarse sand ) 217 forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness ( not less than 2 mm ) , nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the engineer in charge. 218 add for plaster drip course / groove in plastered surface or moulding to r.c.c. projections. 219 cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate ) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 40 mm thick with 20 mm nominal size stone aggregate 220 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete size of tile 600x600 mm 221 providing and laying vitrified floor tiles in different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) , jointing with grey cement slurry @ 3.3 kg / sqm including grouting the joints with white cement and matching pigments etc., complete size of tile 600x600 mm 222 finishing with deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers specifications :painting steel work with deluxe multi surface paint to give an even shade. two or more coat applied @ 0.90 ltr / 10 sqm over an under coat of primer applied @ 0.80 ltr / 10 sqm of approved brand and manufacture 223 finishing with deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers specifications :painting wood work with deluxe multi surface paint of required shade. two or more coat applied @ 0.90 ltr / 10 sqm over an under coat of primer applied @0.75 ltr / 10 sqm of approved brand and manufacture 224 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade : new work ( two or more coats applied @ 1.43 ltr / 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm ) 225 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : new work ( two or more coats ) over and including water thinnable priming coat with cement primer 226 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : new work ( two or more coats ) over and including water thinnable priming coat with cement primer 227 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 228 providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 229 providing and fixing aluminium sliding door bolts, isi marked anodised anodic coating not less than grade ac 10 as per is : 1868 ) , transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm 230 providing and fixing aluminium tower bolts, isi marked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :300x10 mm 231 providing and fixing aluminium handles, isimarked, anodised ( anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screw setc. complete :100 mm 232 providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: ( a ) applying a slurry coat of neat cement using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is. 2645 and approved by engineer in charge over the rcc slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. ( b ) laying brick bats with mortar using broken bricks / brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 ( 1 cement : 5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge over 20 mm thick layer of cement mortar of mix 1:5 ( 1 cement :5 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineer in charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. 233 ( c ) after two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to is : 2645 and approved by engineerin charge. ( d ) finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 ( 1 cement :4 coarse sand ) admixed with water proofing compound conforming to is : 2645 and approved by engineerin charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. 234 ( e ) the whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“all above operations to be done in order and as directed and specified by the engineer in charge : with average thickness of 120 mm and minimum thickness at khurra as 65 mm. 235 providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing epdm gasket, perforated aluminium spacers, desiccants, sealant ( both primary and secondary sealant ) etc. as per specifications, drawings and direction of engineer in charge complete. 236 supplying and fixing rolling shutters of approved make, made of required size m.s. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to is: 4454 part 1 and m.s. top cover of required thickness for rolling shutters.80x1.25 mm m.s. laths with 1.25 mm thick top cover 237 providing and fixing ball bearing for rolling shutters. 238 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, ( i ) single socketed pipes.110 mm diameter 239 providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend 240 providing and fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with m.s. screws of required length, including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand ) and making good the wall etc. complete. 110 mm...

Military Engineer Services - Madhya Pradesh

39252205 tender for provision of guard room with toilet block athffr at inf school under ge ( mis ) mhow; 1 b / r works: 2 surface dressing not exceeding 15 cm deep in soft / loose soil all as specified . 3 excavationover areas not exceeding1.5 m deep and getting out in soft / loose soil complete all as specified 4 m& for moorum / red bajri filling in floors or pavings, laid in layers not exceeding150mm thick, spread, levelled and rammed includingwatering as required complete all as specified 5 returning, filling in soil including spreading, levelling, watering and well ramming in layers not exceeding 25 cm. 6 removing excavated material ( soil ) not exceeding50m and depositing where directed at a level not exceeding 1.5 m above the starting point 7 m&l for plaincement concrete 1:4:8type d2using 40mm graded stone aggregateas in foundation, filling and mass concrete and sub base of floor complete all as specified 8 m&l forrccm 25 grade concrete ( using20mm graded aggregate ) as in foundation, footings, plinth protection and similar rcc works all as specified. note : reinforcement shall be measured and paid separately under relevant item. 9 m&l forrccm 25 grade concrete ( using20mm graded aggregate ) as in slabs supported on walls, , chajjas, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified .note : reinforcementshall be measured and paid separately under relevant item 10 m&l forrccm 25 grade concrete ( using20mm graded aggregate ) as in roof beam, plinth beam, roof beam, lintel beams and columns complete all as specified.note : reinforcementshall be measured and paid separately under relevant item 11 m&l forrccm 25 grade concrete ( using20mm graded aggregate ) as in chajjas complete all as specified .note : reinforcementshall be measured and paid separately under relevant item 12 m&l forrccm 25 grade concrete ( using20mm graded aggregate ) as incolumns, footing, pillars, piers, posts and struts complete all as specified .note : reinforcementshall be measured and paid separately under relevant item 13 m&l for mild steel tmt bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, footing, roof beam, plinth beam, slab, chajjas and similar work hooking ends and binding with and including mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified 14 all as peritem no 12above but 5 mm dia and over up to and including 10 mmdia as in stirrups 15 m&l for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits ( if any ) of foundation and plinth beams; and similar work; vertical or to batter etc.complete rough finished surface of concrete 16 m&l for formwork to sides of pillars, posts, struts, piers, columns and stanchions etc complete rough finished surface of concrete 17 m&l for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick ( horizontal or sloping ) complete rough finished surface of concrete 18 m&l for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.complete rough finished surface of concrete 19 m&l for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of rcc / pcc bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete rough finished surface of concrete 20 m&l for brickwork with modular fly ash bricks, straight or curved on plan exc 6m mean radius, built in cm ( 1:4 ) complete all as specified 21 m&l for 15 mm thick rendering in cm 1:6 onbrick work or concrete surfaces, surfacesfinished even and smooth without using extra cement complete all as specified 22 m&l for 15 mm thick rendering in cm 1:4 onbrick work or concrete surfaces, surfacesfinished even and smooth without using extra cement complete all as specified 23 m&l for 5 mm thick rendering in cm 1:3 onbrick work or concrete surfaces, surfacesfinished even and smooth without using extra cement complete all as specified 24 m&l for 75 mm thick , pcc 1:3:6 type c2 ( using 20mm graded stone aggregate ) as in plinth protection finished the surfaces of concrete topping even and fair ( without using extra cement ) including making joint at every 3 minterval and at corner and filled with mixture of bitumen and sandlaid in alternate bays complete all as specified 25 m&l for preparation of newly plastered surfaces of wall and applying two coat ofsuperiorquality exterior weatherproof water base emulsion paint over a coat of primer of same make on wall completeall as specified and directed. note : ( a ) each stage i.e preparation of surfaces, application of primer, application of first coat.application of second coat shallbe approved by engineer in charge ( b ) written warranty for four years shall befurnished by contractor 26 m&l for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistance primer complete all as specified 27 m&l for preparation of new plastered surfaces of walls and applying three coats of white wash on ceiling surface complete allas specified 28 m&l for machine cut kota stone slab flooring 20 mm thick ( + 2mm ) of size58cm x 58cm ( or nearest size as available in the market ) laid over and including 25 mm thick pcc 1:2:4 type b1 using 20mm graded stone aggregate and 15mm thick screed bedin cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and mirror polishingfinishcomplete all as specified 29 s&fpre painted steel sliding window 3 track, 2 glass panel and 1 mesh panel sliding window fabricated from roll formed sections made of galvanized steel colour coated / powder coated ( base steel as per is 513 ‘d’ quality, galvanized as per is 277 with zinc of 120 gm / sq.mtr ) with total coated thickness of 0.58mm. primer coat with epoxy primer of 5 7 microns thick, finish painted with a polyester paint of 12 16 microns thick and back coated with alkyd backer of 5 7 microns or powder coated with pure polyester powder up to 50 60 microns thick. section for external frame should be of 107x44mm, section for shutter should be of 35x49mm. section of mesh should be of 35 x 49 mm.the windows should be paneled with 5mm thick plain clear glass. corner bracket for internal and external frame made of glass filled nylon. gaskets are to be made of ethyl propylene diamine monomer ( epdm ) .the sections are to be cut to length, joined and assembled by means of corner bracket. the above frames should be fixed to the concrete / masonry walls by means of self expandingscrewscomplete all as specified and directed . 30 s&fair tight windows top hung type made with galvanised steel colour coated / powder coated ( base steel as per is 513 of “d quality, galvanized as per is 277 with zinc of 120 grams / sqm ) with total coating thickness of 0.58 mm, coated sections should be with epoxy primer of 5 7 microns thick, finish painted with a polyester paint of 12 16 microns thick and back coated with alkyd backer 5 7 microns thick or powder coated with pure polyester powder up to 50 60 microns thick, outer frame section 46x52x0.58 mm, shutter section 46x46x0.58mm, mullion section 46x70x0.58mm, beading section 18x25x0.58 mm, windows panelled with 5mm thick plain clear glasswith epdm ( ethyl propylene diamine monomer ) gasket and the sections cut to length mitre joined with corner bracket centre mullions fixed using mullion cap and with handle made of high grade aluminium powder coating and nylon receiver, corner brackets made of crca ( cold rolled close annealed ) with zinc phosphate, mullion caps made of glass filled nylon, frames fixed to the concrete / masonry wall by means of self expanding screws complete all as specified and directed 31 m&l for glazed ceramic coloured tile of size 450mm x 300 mmx6 to 7mm thick as in dados or skirting over and including rendering 10mm thick in cm ( 1:4 ) , jointed in neat grey cement slurry and pointed incolour cement to match colour oftile all specified. 32 m&l for non skid ceramic coloured tiles7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, over andincluding 20mm thick screed bed in cm ( 1:6 ) asin floors etc set and jointed in neat cement slurry and pointed in coloured cement to match colour of tiles allas specified 33 s&fwash hand basins, vitreous china, of size 550x400mm ( flat back, or angle back type ) including cutting for and pinning in ends of brackets or errecting stand exclusive of fixing of supply and waste pipe etc complete all as specified 34 s&fvitreous china squatting pan, ‘orissa’ pattern of size 580 x 440 mm white, with integral foot rests ( excluding flushing cistern and flush pipe ) complete all as specified. 35 s&f pvc valveless, syphonic action type flushing cistern 10 litres capacity , low / high level white with inlet ball valve float and handle including brackets complete all as specified 36 s&fvitreous china urinal half stall type 350x390x600 mm ( minimum ) height with including providing & fixing of plugs bedding against wall in cement mortar 1:2 pointing around urinal back in cement mortar complete all as specified. 37 s&f cp brass urinal spreader suitable for 15 mm dia pipe. 38 s&f urinal partition of size 900x450 mm with hpl board 10 to 12mmthickfixed with brackets complete all as specified 39 s&f pvc waste pipe40mm / 32mm bore suitable for wash hand basin / sink / urinal outlet complete all as specified & directed. 40 s&f 75 mm bore pvcfloor traps plain with grating and 300 mm long out let including necessary jointing 41 s&f pvc pipe 40 mm dia, in any length and in any position such as walls, ceiling or laid in floor or trenches etc. complete all as specified 42 s&f pvc bend for 40mm dia pvc pipe 43 s&fpvc bends 75mm bore, any radius 44 s&fpvc ( swr ) pipe 110 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified 45 s&fpvc ( swr ) pipe 75 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified 46 s&f bib taps ( push type ) cast copper alloychromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm borecomplete all as specified 47 s&f fancy type chromium plated two way bib cock of 15mm bore, screwed for iron pipe or brass ferrule etc complete all as specified . 48 s&f pillar taps ( swan neck ) , fancy typecast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore, complete all as specified 49 s&f stop / angle cock cast copper alloy high pressure, angle valve type, chromium plated suitable for 15mm bore steel pipecomplete all as specified 50 s&fhealth faucet with stainless steel flexible pipe of 1.00 to 1.50 metrelength including holdercomplete all as specified 51 s&f pvc connection of 450mm longsuitable for 15mm dia iron pipe including ptmt nuts complete all as specified 52 s&f 15mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified 53 all as per serial item no.51 abovebutfor 20mm bore. 54 s&fgun metal, globe or gate valve 15mm dia with iron wheel head , screwed both ends for iron pipe and fixed. 55 s&f 20mm boreball valve highpressure of ptmt with epoxy coated aluminium rod and high density plastic ball screwed for iron pipecomplete all as specified 56 s&f rotational moulded polythylenewater storage tank 500 litres capacitydouble layered , cylindrical , vertical with closte top , hoisted and fixed in position all as specified in ssr part icomplete 57 s&f sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm vide with chromium plated bracket guard and railing 60cm long complete. 58 s&fbevelled edge mirror of 5 to 6 mm thick selected quality glass of size 600 x 450 mm mounted on 6mm thickac building board or commercial plywood andfixed to wooden plug with chromium plated brass screw and cup washers complete complete all as specified 59 s&f pressed steel frame of size 105 mmx60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified 60 s&f steel door including projecting type hinges, steel handle, complete, with glazing bars, dovetailed or welded complete 61 s&f pvc door frame of size 50mm x 47 mm made out of 5 mm prelam pvc sheet reinforced with ms square tube in opening of suitable size complete all as specified 62 s&f factory made ( prelam on both sides ) solid panel pvc door shutter 30 mm thick ( style ) consisting of frame made out of ms tubes for top and bottom rails, ms frame shall covered with heat moulded prelam pvc c channel having a pvc sheet strip of 20 mm width stuck inside with solvent cement for styles and prelampvc sheets for top rail, lock rail and bottom rail in either side and as gap insert for top rail and bottom rail pannelling of prelam pvc sheet to be filled in the ms welded / sealed to the styles and rails with suitable pvc sheet beading and jointed together wiht solvent and fixing in the frame at site as per specification and drawing complete all as specified 63 s&f 100mm long butt hinges medium weight cold rolled mild steel complete all as specified 64 s&faluminium anodized barrel tower bolts of length 150mm of extruded section 65 s&fmild steel pressed handle of size 150 mm, oval type, stove enamelled black complete all as specified 66 m&l for preparation of surfaces for applying bituminous primer ( conforming to is 3384 1965 ) @ 0.40 kg / sqm complete. 67 m&l for applying a tack coat of industrial bitumen grade of 85 / 25 at the rate of 1.2 kg per sqm including cleaning surfaces complete all as specified 68 m&lfor app based polymeric membrane minimum weighing 3kg / sqm and minimum 3mm thick reinforced with polyster non woven fabric ( weightnot less than 150 gm / sqm ) laid on primed surface by forced application complete all as specified 69 m&l for applying two coats of bitumen based aluminium painting @ 0.15 kg / sqm each coat on water proofing treatment includingpreparation of surface as on non assesible area complete all as specified 70 e / m portion: 71 m&l for point wiring with fr lshpvc insulated pvc unsheathed electriccable 1100v grade single core having multi stranded copper conductor of size 1.5 sqmm nominal cross sectional area drawn in & including non metallic rigid pvc conduit isi marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good and matching disturbed surface of wall with existing surface of wall ( cutting except on ceiling for fan point only, on ceiling instead of pvc conduit surface casing caping shallbe used ) & 1.5 sqmm green fr lspvc insulated unsheathed copper conductor as earth wire connected to commonearth dolly by providing lugs including galvanised boxes and bakelite sheetfor mounting switches, sockets, fan regulators etc for one light point / fan point controlled by one switch. make of pvc conduit / casing caping: plaza / finolex / polycab / kalinga / jindal / asian. 72 one light point controlled by one switch 73 one exhaust fan point controlled by one switch 74 one 5 amps socket out let point controlled by one switch on same board with other switches. 75 one 5 amps socket out let point on independent board controlled by one switch. 76 all as per item no 69 here in before but using pvc insulated unsheathed 2.5 sqmm cross sectional area cable for phase / neutral & for earth 2.5 sqmm green pvc insulated cable for 15 amps socket point on independent board controlled by one switch. 77 s&f switchpiano flush button single pole one way 6 amp 240 volt 78 s&f socket outlet flush type 5 pin, 6 amps, 230 volts 79 s&f switch piano flush button single pole one way 15 amp 240 volt 80 s&f socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 amp, 230 volts 81 s&f ceiling rose surface bakelitethree terminal 82 s&f electronic fan regulator step type 83 s&f integrated led tube light fitting 1x18 / 20 watt, 6000kcomplete fitting with all accessories duly connection with three core flexible coppercable duly fixed on two nos of pvc square boxescomplete all as specifiedmake: havells cat no. lhexblp7pn1w018 , bajaj cat pt no. bclsb 18whor otherequivalent in wipro 84 s&f integrated led tube light fitting 1x9 / 10 watt, 6000kcomplete fitting with all accessoriesduly connection with three core flexible coppercable duly fixed on two nos of pvc square boxcomplete all as specified and directed. make: havells cat no. lhexblp7in1w009 bajaj cat pt no. bclsb 10 wh or other equivalent in wipro 85 s&f led street light fittings 1x30 watt, 5700k complete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & ip 65 protection fixed on and including sufficient length and appropriate size gi bracket with all accessories duly connection with three core flexible copper cable complete all as specified make: havells cat no.lhexayp7pn6k030 crompton cat no. lsto 25 cdl, bajaj cat no. bclst 25w led iv2 86 s&f double door tpn dbs four wayof powder coated dbs suitable for mcbs fitted with bus bar, neutral link, earth bar and din ral complete all as specified make: hpl / l&t / hpl / havells 87 s&f double door spn dbs 4 wayof powder coated dbs suitable for mcbs fitted with bus bar, neutral link, earth bar and din ral complete all as specified 88 s&f double door spn dbs 8 wayof powder coated dbs suitable for mcbs fitted with bus bar, neutral link, earth bar and din ral complete all as specified 89 s&f mcb tpn 40 to 100 amps415v 10ka c curve fixedindb complete 90 s&f mcb spn 6 to 32 amps10 ka, b series including connection with suitable size aluminium / copper lugs complete all as specified 91 s&f mcb sp 240 volts 6 to 32 amps, 10 ka breaking capacity, b series including connection with suitable size aluminium / copper lugs complete all as specified 92 s&f ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 v, 1200 mm sweep. minimumair delivery 210 cfm with service value 6.00 bee. 5star rated with brushless direct current motor ( bldc ) . complete all as specified make: havells / bajaj / crompton. 93 m&l for sub main wiringwith two runs of single core frlspvc insulated unsheathed cable 1100 volts grade, 4 sqmm size with multistranded copper conductor, drawn in and including non metallic rigid pvc conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including frls pvc insulated unsheathed 4.0 sqmm cable with multistranded copper conductor green pvc insulated as continuous earth conductor cable connected to earth dolly from main distribution board complete all as specified . 94 s&f exhaust fan 300mm sweep, ac single phase 230 volts, metallic type, complete with louverincluding electric connection with suitable size copper conductor cable, clamps, nuts, bolts etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall tomatch with the existing surface of wall complete all as specified and directed by engineer in charge. make : havells model:ventil air dx white or otherequivalent in / bajaj / crompton. 95 m&l for earthing complete with galvanized steel earth plate electrode 60cm x 60cmx 6.3 mm thick buried directly in ground ( earth pit not less than 2.25 meter deep below ground level ) with the top edge of the earth plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate no.5 of messsr parts i and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of pcc earth chamber in mix 1:3:6 type c1 , 40 mm thick rcc 1:2:4 type b1cover reinforced with 8mm dia ms bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia gi light grade and 15mm dia light grade pipe for earth lead protection and testing on completionall as specified and directed. 96 excavation in trenche not exceeding 1.5m wide andnot exceeding 1.5m indepthgetting out in hard / dense soil for laying cable / errecting poles , stay assembly all as specified. 97 returning and filling in soil including spreading levelling watering and well ramming in layers not exceeding 25cm all as specified. 98 removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point. 99 s&f medium grade galvanised iron tube with all fittings and fixed completeon walls and ceilings or laid on floors of 50 mm bore 100 s&f medium grade galvanised iron tube with all fittings and fixed completeon walls and ceilings or laid on floors of 25 mm bore 101 s&f ballvalves, high pressure of ptmt with epoxy coated aluminium rod & high density plastic ballscrewed for iron pipe and fixed suitable for 25mm bore dia of pipe ( minimum weight 455 gms ) 102 supply, lowering, install, testing and commissioning submersible pump set of capacity 10 hp slip start synchronous run motor ( s4rm / bldc type ) , pump 20 stage, 143 metrewith ss 304 impeller, shaft duplex steel, casing ss 304, pump motor ss 304 suitable for 6 bore well includingsuitable control panel for pumpset , smart vfd driven with phase reversal protection, dry run protection, over & under voltage protection, fault indication alarm, energy monitoring and remote monitoring system for access through mobile or computer by manufacturer application for 5 year of period by providing sim card. including provision ofms cover for borewell and suitable clamp to hold the submersible pumpset including provision of suitable size rope of required length complete all as specified and directed by engineer in charge. 103 s&fpvc insulated sheathed 1100 volt grade copper conductor cable flat multi stranded for submersible pumps of3 core 6 sqmm as in motorsforbore well all as specified and directed...

Ministry Of Communication - Madhya Pradesh

38840200 tender for construction of small po building at harsud in khandwa division under indore region mp. 1 earth work 1.1 earth work in excavation by mechanical means (hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer in charge. 1.1.1 all kinds of soil 50 cum 149.00 7450.00 1.2 earth work in excavation by mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1.2.1 all kinds of soil. 39 cum 218.60 8525.00 1.3 excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 1.3.1 all kinds of soil 1.3.1.1 pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 20 metre 293.40 5868.00 1.4 filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 36 cum 161.60 5818.00 1.5 excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 227 cum 564.00 128028.00 1.6 extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. 1.6.1 all kinds of soil 1 cum 104.50 105.00 1.7 supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 12 cum 2161.20 25934.00 sub total 181728.00 2 cement concrete (cast in situ) 2.1 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level : 2.1.1 1:2:4 (1 cement : 2 coarse sand (zone iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 6 cum 7365.15 44191.00 2.1.2 1:5:10 (1 cement : 5 coarse sand (zone iii) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 35 cum 6050.65 211773.00 2.2 providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 2.2.1 1:2:4 (1 cement : 2 coarse sand (zone iii) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 1 cum 9047.30 9047.00 2.3 centering and shuttering including strutting, propping etc. and removal of form work for : 2.3.1 retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. 7 sqm 702.00 4914.00 2.4 making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone iii) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 16 sqm 681.65 10906.00 sub total 280831.00 3 reinforced cement concrete 3.1 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level : 3.1.1 1:1.5:3 (1 cement : 1.5 coarse sand (zone iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) 30 cum 8364.20 250926.00 3.2 reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fllets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: 3.2.1 1:1.5:3 (1 cement : 1.5 coarse sand(zone iii) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 5 cum 9861.70 49309.00 3.3 reinforced cement concrete work in beams, suspended foors, roofs having slope up to 15* landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to foor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone iii) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). 23 cum 10391.40 239002.00 3.4 centering and shuttering including strutting, propping etc. and removal of form for 3.4.1 foundations, footings, bases of columns, etc. for mass concrete 18 sqm 332.10 5978.00 3.4.2 walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 28 sqm 702.00 19656.00 3.4.3 suspended floors, roofs, landings, balconies and access platform 115 sqm 766.55 88153.00 3.4.4 lintels, beams, plinth beams, girders, bressumers and cantilevers 99 sqm 608.35 60227.00 3.4.5 columns, pillars, piers, abutments, posts and struts 70 sqm 804.25 56298.00 3.4.6 weather shade, chajjas, corbels etc., including edges 12 sqm 814.95 9779.00 3.5 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 3.5.1 thermo mechanically treated bars of grade fe 500d or more. 3976 kg 89.65 356448.00 3.6 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 3.6.1 thermo mechanically treated bars of grade fe 500d or more. 3907 kg 89.65 350263.00 3.7 smooth finishing of the exposed surface of r.c.c. work with 6 mm thick cement mortar 1:3 (1 cement : 3 fine sand). 196 sqm 253.05 49598.00 3.8 add for plaster drip course/ groove in plastered surface or moulding to r.c.c. projections. 21 metre 64.70 1359.00 sub total 1536996.00 4 masonry work 4.1 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in foundation and plinth in: 4.1.1 cement mortar 1:6 (1 cement : 6 coarse sand) 34 cum 6658.25 226381.00 4.2 brick work with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : 4.2.1 cement mortar 1:6 (1 cement : 6 coarse sand) 18 cum 8288.35 149190.00 4.3 half brick masonry with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor v level. 4.3.1 cement mortar 1:4 (1 cement :4 coarse sand) 60 sqm 1018.05 61083.00 4.4 extra for providing and placing in position 2 nos 6mm dia. m.s. bars at every third course of half brick masonry. 60 sqm 86.45 5187.00 4.5 brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). 29 metre 55.80 1618.00 sub total 443459.00 5 cladding work 5.1 providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. 5.1.1 granite stone slab of colour black, cherry/ruby red 5.1.1.1 area of slab upto 0.50 sqm 6 sqm 4679.35 28076.00 5.2 providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. 5.2.1 granite work 47 metre 418.85 19686.00 5.3 providing and fixing ist quality ceramic glazed wall tiles conforming to is: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 50 sqm 1063.45 53173.00 5.4 (a) designing, fabricating, testing, installing and fixing in position curtain wall with aluminium composite panel cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) providing, fabricating and supplying and fixing panels of aluminium (c) composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick fr grade mineral core sandwiched between two aluminium sheets (each 0.5mm thick). the aluminium composite panel cladding sheet shall be coil coated, with kynar 500 based pvdf / lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. the fastening brackets of aluminium alloy 6005 t5 / ms with hot dip galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, ss 316 pins and anchor bolts of approved make in ss 316, nylon separators to prevent bi metallic contacts all complete required to perform as per specification and drawing the item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. base frame work for acp cladding is payable under the relevant aluminium item.s the contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the engineer in charge. however, for the purpose of payment, only the actual area on the external face of the curtain wall with aluminum composite panel cladding (including width of groove) shall be measured in sqm. up to two decimal places. 22 sqm 4474.20 98432.00 sub total 199367.00 6 wood and p. v. c. work 6.1 providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 6.1.1 sal wood 0.17 cum 106720.85 18143.00 6.2 providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. 6.2.1 sal wood 0.12 cum 97078.35 11649.00 6.3 providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 6.3.1 35 mm thick including isi marked stainless steel butt hinges with necessary screws 9 sqm 2015.75 18142.00 6.4 extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 9 sqm 401.40 3613.00 6.5 providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with isi, is : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. 3 each 1025.65 3077.00 6.6 providing and fixing aluminium sliding door bolts, isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 6.6.1 300x16 mm 6 each 260.30 1562.00 6.6.2 250x16 mm 4 each 234.90 940.00 6.7 providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 6.7.1 200x10 mm 6 each 90.80 545.00 6.7.2 150x10 mm 4 each 75.55 302.00 6.8 providing and fixing aluminium handles, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 6.8.1 125 mm 12 each 60.05 721.00 6.8.2 100 mm 8 each 53.25 426.00 6.9 providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 6.9.1 twin rubber stopper 6 each 62.25 374.00 6.1 providing & fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to is : 2046 type s, including cost of adhesive of approved quality. 6.10.1 1.0 mm thick 11 sqm 764.00 8404.00 6.11 providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of engineer in charge (frame work shall be paid for separately). 6.11.1 12mm thick commercial ply conforming to is : 1328 bwr type 11 sqm 1084.60 11931.00 sub total 79829.00 7 steel work 7.1 providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of t iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. 7 sqm 9397.35 65781.00 7.2 steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 7.2.1 in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 802 kg 142.30 114125.00 7.3 providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 109 kg 612.25 66735.00 sub total 246641.00 8 flooring 8.1 providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to is : 15622 of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 12 sqm 935.60 11227.00 8.2 providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 8.2.1 size of tile 600x600 mm 57 sqm 1416.65 80749.00 8.3 providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to i.s. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. 8.3.1 size of tile 600x600 mm 4 sqm 1466.50 5866.00 8.4 providing and laying polished granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the engineer in charge. 8.4.1 polished granite stone slab colour of black, cherry/ruby red or equivalent 12 sqm 3908.80 46906.00 sub total 144748.00 9 roofing 9.1 making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over p.v.c. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 2 each 266.60 533.00 9.2 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes. 9.2.1 110 mm diameter 8 metre 319.75 2558.00 9.3 providing and fixing on wall face unplasticised pvc moulded fittings/ accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion 9.3.1 coupler 9.3.1.1 110 mm 2 each 119.95 240.00 9.3.2 bend 87.5° 9.3.2.1 110 mm bend 2 each 132.00 264.00 9.3.3 shoe (plain) 9.3.3.1 110 mm shoe 2 each 115.95 232.00 9.4 providing and fixing unplasticised pvc pipe clips of approved design to unplasticised pvc rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with m.s. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 9.4.1 75 mm 3 each 309.50 929.00 9.4.2 110 mm 9 each 310.85 2798.00 sub total 7554.00 10 finishing 10.1 12 mm cement plaster of mix : 10.1.1 1:6 (1 cement: 6 coarse sand) 176 sqm 294.35 51806.00 10.2 15 mm cement plaster on rough side of single or half brick wall of mix: 10.2.1 1:6 (1 cement: 6 coarse sand) 143 sqm 339.10 48491.00 10.3 20 mm cement plaster of mix : 10.3.1 1:6 (1 cement: 6 coarse sand) 13 sqm 401.35 5218.00 10.4 6 mm cement plaster of mix : 10.4.1 1:3 (1 cement : 3 fine sand) 5 sqm 253.05 1265.00 10.5 neat cement punning. 23 sqm 67.80 1559.00 10.6 extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. 2 per bag of 50kg cement used in the mix 60.55 121.00 10.7 distempering with 1st quality acrylic distemper (ready mixed) having voc content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification. 10.7.1 two or more coats on new work 152 sqm 92.75 14098.00 10.8 applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 10.8.1 water thinnable cement primer 283 sqm 64.45 18239.00 10.9 finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: 10.9.1 new work (two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 224 sqm 162.35 36366.00 10.1 wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : 10.10.1 two or more coats on new work 131 sqm 137.85 18058.00 10.11 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 10.11.1 two or more coats on new work 49 sqm 131.45 6441.00 10.12 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 131 sqm 123.85 16224.00 sub total 217886.00 11 road work 11.1 supplying at site : 11.1.1 r.c.c. standards post/ struts/rails/ pales of mix 1:1.5:3(1 cement : 1.5 coarsesand : 3 graded stone aggregate12.5 mm nominal size) with wooden plugs or 6mm barnibs wherever required as per direction of engineer incharge (cost of earth works in excavation, concrete worksin foundation to be paid separately). 1.2 cum 29105.40 34926.00 11.2 fencing with r.c.c. post placed at required distance, embedded incement concrete blocks, every 15th post, last but one end post andcorner post shall be strutted on both sides and end post one sideonly, provided with horizontal lines and two diagonals of barbed wireweighing 9.38 kg per 100 metres (minimum), between the two postsfitted and fixed with g.i. staples on wooden plugs or g.i. binding wiretied to 6 mm bar nibs fixed while casting the post (cost of r.c.c.posts, struts, earth work and concrete to be paid for separately) : payment to be made per metre cost of total length of barbed wire used. 11.2.1 with g.i. barbed wire 829 metre 12.45 10321.00 11.3 providing and laying tactile tile (for vision impaired persons as perstandards) of size 300x300x9.8mm having with water absorption lessthan 0.5% and conforming to is:15622 of approved make in all coloursand shades in for outdoor floors such as footpath, court yard, multimodals location etc., laid on 20mm thick base of cement mortar 1:4(1 cement : 4 coarse sand) in all shapes & patterns including groutingthe joints with white cement mixed with matching pigments etc.complete as per direction of engineer in charge. 10 sqm 1719.00 17190.00 11.4 providing and laying factory made chamfered edge cement concretepaver blocks in footpath, parks, lawns, drive ways or light trafficparking etc, of required strength, thickness & size/ shape, made bytable vibratory method using pu mould, laid in required colour &pattern over 50mm thick compacted bed of sand, compacting andproper embedding/laying of inter locking paver blocks into the sandbedding layer through vibratory compaction by using plate vibrator,filling the joints with sand and cutting of paver blocks as per requiredsize and pattern, finishing and sweeping extra sand. complete all asper direction of engineer in charge. 11.4.1 60mm thick cement concrete paver block of m 35 gradewith approved colour, design & pattern. 310 sqm 932.35 289029.00 sub total 351466.00 12 sanitary installations 12.1 providing and fixing white vitreous china pedestal type water closet(european type w.c. pan) with seat and lid, 10 litre low level whitep.v.c. flushing cistern, including flush pipe, with manually controlleddevice (handle lever), conforming to is : 7231, with all fittings andfixtures complete, including cutting and making good the walls andfloors wherever required : 12.1.1 w.c. pan with isi marked white solid plastic seat and lid 3 each 5540.55 16622.00 12.2 providing and fixing wash basin with c.i. brackets, 15 mm c.p. brasspillar taps, 32 mm c.p. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the wallswherever require: 12.2.1 white vitreous china flat back wash basin size 550x400 mm with single 15 mm c.p. brass pillar tap 3 each 1679.60 5039.00 12.3 providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube upto1 metre long with s.s. triangular plate to eureopean type w.c. ofquality and make as approved by engineer in charge. 3 each 299.35 898.00 12.4 providing and fixing white vitreous china flat back or wall corner typelipped front urinal basin of 430x260x350 mm or 340x410x265 mmsizes respectively. 1 each 1382.30 1382.00 12.5 providing and fixing mirror of superior glass (of approved quality) andof required shape and size with plastic moulded frame of approvedmake and shade with 6 mm thick hard board backing : 12.5.1 rectangular shape 453x357 mm 3 each 1158.95 3477.00 12.6 providing and fixing toilet paper holder : 12.6.1 c.p. brass 3 each 680.80 2042.00 12.7 providing and fixing ptmt waste coupling for wash basin and sink,of approved quality and colour. 12.7.1 waste coupling 38 mm dia of 83 mm length and 77mmbreadth, weighing not less than 60 gms 4 each 109.70 439.00 12.8 providing and fixing ptmt bottle trap for wash basin and sink. 12.8.1 bottle trap 38 mm single piece moulded with height of270 mm, effective length of tail pipe 260 mm from thecentre of the waste coupling, 77 mm breadth with 25 mmminimum water seal, weighing not less than 263 gms 3 each 325.10 975.00 12.9 providing and fixing ptmt liquid soap container 109 mm wide, 125mm high and 112 mm distance from wall of standard shape withbracket of the same materials with snap fittings of approved qualityand colour, weighing not less than 105 gms. 3 each 146.30 439.00 12.1 providing and fixing ptmt urinal cock of approved quality and colour. 12.10.1 15 mm nominal bore, 80 mm long, 42 mm high and 30mmwide with bsp female threads weighing not less than 48 gms 1 each 149.95 150.00 sub total 31463.00 13 water supply 13.1 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. internal work exposed on wall 13.1.1 25 mm nominal dia pipes 2 metre 408.55 817.00 13.1.2 32 mm nominal dia pipes 15 metre 500.95 7514.00 13.1.3 40 mm nominal dia pipes 10 metre 674.35 6744.00 13.2 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply, including all cpvc plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. concealed work, including cutting chases and making good the walls 13.2.1 20 mm nominal dia pipes 16 metre 513.75 8220.00 13.2.2 25 mm nominal dia pipes 7 metre 626.05 4382.00 13.3 providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot & cold water supply including all cpvc plain & brass threaded fittings this includes jointing of pipes & fittings with one step cpvc solvent cement, trenching, refilling & testing of joints complete as per direction of engineer in charge. external work 13.3.1 25 mm nominal dia pipes 10 metre 370.65 3707.00 13.3.2 50 mm nominal dia pipes 3 metre 811.85 2436.00 13.4 providing and fixing gun metal gate valve with c.i. wheel of approved quality (screwed end) : 13.4.1 25 mm nominal bore 2 each 532.35 1065.00 13.5 providing and fixing ball valve (brass) of approved quality, high or low pressure, with plastic floats complete : 13.5.1 25 mm nominal bore 1 each 399.15 399.00 13.6 providing and fixing uplasticised pvc connection pipe with brass unions : 13.6.1 45 cm length 13.6.1.1 15 mm nominal bore 7 each 85.20 596.00 13.7 providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 1000 per litre 9.70 9700.00 13.8 providing and fixing ptmt bib cock of approved quality and colour. 13.8.1 15mm nominal bore, 86 mm long, weighing not less than 88 gms 3 each 109.85 330.00 13.9 providing and fixing ptmt stop cock of approved quality and colour. 13.9.1 15 mm nominal bore, 86 mm long, weighing not less than 88 gms 7 each 103.15 722.00 13.1 providing and fixing ptmt grating of approved quality and colour. 13.10.1 rectangular type with openable circular lid 13.10.1. 1 150 mm nominal size square 100 mm diameter of the inner hinged round grating 4 each 169.70 679.00 13.11 providing and fixing ptmt soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms. 3 each 96.75 290.00 13.12 providing and fixing ptmt extension nipple for water tank pipe, fittings of approved quality and colour. 13.12.1 25mm nominal bore, weighing not less than 62 gms 2 each 100.55 201.00 sub total 47802.00 14 drainage 14.1 providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all round upvc type b pipes including bed concrete as per standard design : 14.1.1 110 mm diameter upvc type b pipe 8 metre 895.50 7164.00 14.1.2 160 mm diameter upvc type b pipe 12 metre 1095.15 13142.00 14.2 providing and fixing square mouth s.w. gully trap class sp 1 complete with c.i. grating brick masonry chamber with water tight c.i. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 14.2.1 100x100 mm size p type 14.2.1.1 with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 3 each 2453.55 7361.00 14.3 providing and laying non pressure np2 class (light duty) r.c.c. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 14.3.1 300 mm dia. r.c.c. pipe 5 metre 902.05 4510.00 14.4 constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with r.c.c. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone iii) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone iii) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : 14.4.1 inside size 90x80 cm and 45 cm deep including c.i. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 14.4.1.1 with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 3 each 11687.10 35061.00 14.5 extra for depth for manholes : 14.5.1 size 90x80 cm 14.5.1.1 with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 1 metre 8127.45 8127.00 14.6 providing m.s. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : 14.6.1 with 20x20 mm square bar 2 each 461.35 923.00 14.7 providing and fixing in position pre cast r.c.c. manhole cover and frame of required shape and approved quality 14.7.1 l d 2.5 14.7.1.1 rectangular shape 600x450 mm internal dimensions 2 each 1255.25 2511.00 14.8 making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and s.w. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 14.8.1 with common burnt clay f.p.s. (non modular) bricks of class designation 7.5 1 each 28029.15 28029.00 sub total 106828.00 15 aluminium work 15.1 providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. (glazing, paneling and dash fasteners to be paid for separately) : 15.1.1 for fixed portion 15.1.1.1 powder coated aluminium (minimum thickness of powder coating 50 micron) 50 kg 466.30 23315.00 15.1.2 for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber / neoprene gasket required (fittings shall be paid for separately) 15.1.2.1 powder coated aluminium (minimum thickness of powder coating 50 micron) 50 kg 553.55 27678.00 15.2 providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . (cost of aluminium snap beading shall be paid in basic item): 15.2.1 with float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) 15 sqm 1019.80 15297.00 sub total 66290.00 16 water proofing 16.1 grading roof for water proofing treatment with 16.1.1 cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) 9 cum 7510.75 67597.00 16.2 providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having sun reflectivity index (sri) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. one coat of self priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). the operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of engineer in charge. 87 sqm 474.15 41251.00 sub total 108848.00 17 structural glazing alumminium composite panel 17.1 providing and supplying aluminium extruded tubular and otheraluminium sections as per the architectural drawings and approvedshop drawings , the aluminium quality as per grade 6063 t5 or t6 asper bs 1474,including super durable powder coating of 60 80 micronsconforming to aama 2604 of required colour and shade as approvedby the engineer in charge. ( the item includes cost of material suchas cleats, sleeves, screws etc. necessary for fabrication of extrudedaluminium frame work. nothing extra shall be paid on this account).the weight of aluminium extruded section shall be taken for purposeof payment. 21 kg 370.45 7779.00 sub total 7779.00 18 new technologies and materials 18.1 providing an fixing factory made single extruded wpc (wood polymer composite) solid wood/ window/ clerestory window frames/ chowkhat comprising of virgin pvc polymer of k value 58 60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100gms) fabricated with miter joints after applying pvc solvent cement and screwed with full body threaded star headed ss screws having minimum frame density of 750kg/cum, screw withdrawal strength of 2200n (face) & 1100n (edge), minimum compressive strength of 58n/mm2 and modulus of elasticity 900n/mm2 and resistance of spread of flame of class a category with property of being termite/ borer proof, water /moisture proof and fire retardant and fixed in position with m.s. hold fast/ lugs/ ss dash fasteners of required dia and length complete as per direction of engineer in charge, (m.s. hold fast/lugs or ss dash fasteners shall be paid for separately) note: for wpc (wood polymer composite) solid wood/ window frames minus 5mm tolerance to dimensions i.e. depth and width of profile shall be acceptable. variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 18.1.1 frame size 45x 70mm 20 metre 632.25 12645.00 18.2 providing and fixing factory made single extruded wpc (wood polymer composite) solid plain flush door shutter of required size comprising of virgin polymer of k value 58 60 (suspension grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 n (face) & 900 n (edge), minimum compressive strength 50 n/mm2, modulus of elasticity 850 n/mm2 and resistance to spread of flame of class a category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk s.s screws, all as per direction of engineer in charge. (note: stainless steel butt hinges and necessary s.s screws shall be paid separately) 18.2.1 30 mm thick 6 sqm 3954.00 23724.00 sub total 36369.00 19 market rate items 19.1 providing & fixing of customer writing ledge of size 1220mm long, 400mm wide and 1450mm high with writing top at a height of 1050mm including open drawers of 100mm depth for keeping papers below the working top as per architectural drawing no.b1 to b5. the writing ledge shall be made with 19mm thick block board conforming to is 1659/1979 bonded with phenol formaldehyde synthetic resin of is 840/1974 of approved make duro/century/green/archidiam or equivalent including backing also of 19mm thick block board of full height of 1450mm. the ledge shall be laminated with 1.00mm thick decorative laminate of greanlam /virgolam/archidiam on all visible surfaces from outside as well as inside and all hidden surfaces shall be painted with white synthetic enamel paint over priming coat of approved quality. all exposed edges of block board shall be covered by 19mm wide and 3mm thick 2nd class teak wood margin including matching the same. a stainless steel dustbin of 450mm height shall also be provided as per drawing. the dustbin shall be made of 1mm thick stainless steel sheet (ss 304 grade) with necessary argon welding wherever required. the work shall include cost of all operations, labour and material, adhesive, nails, stainless steel screws etc. including approval of samples all completed as per direction of engineer in charge. 1 each 10816.00 10816.00 19.2 providing and fixing wooden customer service counter of size 1500mm length and 300mm width having height of 1050mm with attachment of working top having height of 750mm and of l shape having legs of 1500mmx300mm and 1350mmx450mm with tape rings all joints of legs including arrangement of computer system as keyboard, slit for printer paper etc. complete as per drg. no.a1 to a6. the two numbers stainless steel rectangular tube of size 25mmx50mm of 2mm thick having height of 2100mm fitted with counter to support the overhead signage panel as per drg. the counter shall be made of following ingredients : (a) the 19mm thick block board conforming to is 1659/1979 bonded with phenol formaldehyde synthetic resin of is 840/1974 of approved make duro/century/green/archidiam or equivalent shall be used to prepare counter & decorative laminate on outer face and inside face finished with white synthetic enamel paint over priming coat of approved quality. (b) the edges of board shall be covered by 19mm wide and 3mm thick ii class teak wood margin and matching the same. (c) the keyboard and drawer shall be fitted with a pair of 300mm long powder coated telescopic channels of approved brand. (d) the shutter below drawer in the counter shall be fitted with m.s. piano type hinges isi marked conforming to (e) the shutter of counter shall be provided with 2 nos. magnetic catcher of heavy duty (twin strip) horizontal type best quality, 3 nos. multipurpose cabinet lock of godrej make or equivalent and 4 nos. brass finished stainless steel handle of 75mm long of best quality. the work shall include all operations, labour and materials, adhesive, nails and stainless steel screws etc. including approval of sample complete as per drg. and direction of engineer in charge. 3 each 36000.00 108000.00 19.3 providing and fixing storage cupboards as per drawing no.c1 to c4. the cupboard shall be fabricated with following material and operation : a) the 19mm thick block board conforming to is 1659/1979 bonded with phenol formaldehyde synthetic resin of is 840/1974 of approved make duro/century/green/archidiam or equivalent shall be used to prepare the cupboard. b) all exposed outer surface of whole cupboard shall be laminated with 1.00 mm thick decorative laminate of greenlam/virgolam/archidiam and inside, backside and bottom surface shall be finished with white synthetic enamel paint over priming coat. the paint and primer shall be of approved quality. c) all exposed edges of ply shall be covered with 18 mm wide and 3 mm thick 2nd class teakwood margin including matching the same. d) the 18 mm thick cupboard shutter shall be fitted with is : 12817 marked s.s. butt hinges of size 75 x 47 x 1.80 mm with s.s. screws. 19.3.1 (i) storage cupboard of size 1220mm x 400mm x 1050mm containing three boxes with magnetic catcher of heavy duty and horizontal type (triple strip), brush finish stainless steel handles of suitable size (75mm or 100mm) and multipurpose cabinet lock of godrej or equivalent in each box as per drawing and direction of engineer in charge. the work shall include cost of all operations, labour and materials, adhesive, nails, stainless steel screews etc. as above including approval of sample as per direction of engineer in charge. note : nomenclature of item shall supersede over the drawings in case of any ambiguity between the two. 1 each 11430.00 11430.00 19.3.2 (ii) storage cupboards of size 799mm x 400mm x 1050mm containing two boxes with magnetic catcher of heavy duty and horizontal type (triple strip), brush finish stainless steel handles of suitable size (75mm or 100mm) and multipurpose cabinet lock of godrej or equivalent in each box as per drawing and direction of engineer in charge. the work shall include cost of all operations, labour and materials, adhesive, nails, stainless steel screws etc. as above including approval of sample as per direction of engineer in charge. note : nomenclature of item shall supersede over the drawings in case of any ambiguity between the two. 3 each 8175.00 24525.00 19.4 providing & fixing upvc soil, waste & vent pipe conforming to is : 13592 type b of approved brand with necessary solvent etc complete as per direction of engineer in charge. 19.4.1 75 mm diameter 13 metre 432.00 5616.00 19.4.2 110 mm diameter 14 metre 622.66 8717.00 19.4.3 160 mm diameter 12 metre 898.34 10780.00 19.5 providing & fixing moulded fittings conforming to is : 13592 type b of approved brand with necessary solvent etc complete as per direction of engineer in charge. 19.5.1 single tee with door. (a) 75x75x75 mm. 3 each 188.87 567.00 19.5.2 single tee with door. (b) 110x110x110 mm. 3 each 372.30 1117.00 19.5.3 vent cowl. (a) 75 mm. 6 each 80.94 486.00 19.5.4 vent cowl. (b) 110 mm. 3 each 103.23 310.00 19.5.5 nani trap of self cleansing design 110 mm to 75 mm 7 each 211.16 1478.00 19.5.6 plain bend with door with 87.5 degree. (a) 75 mm. 3 each 145.47 436.00 19.5.7 plain bend with door with 87.5 degree. (a) 110 mm. 3 each 226.41 679.00 sub total 184957.00 total 4280841.00 add difference of gst @ 6.33% (gst raised from 12% to 18%) @6.33% on sr&dr total 40,95,884.00 259269.00 total 4540110.00 less cost index @2% on sr&dr total 43,55,153.00 87103.00 grand total 4453007.00 sh i (wiring) 1 wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with modular switch, modular plate, suitable gi box and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable i/c making good the damages up to its original finish etc as required.(accessories to be used of mk blanze /legrand aretior/anchor vision ) 1.1 group c 44 points 1467.00 point 64548.00 2 wiring for circuit/ submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit i/c making good the damages up to its original finish as required 2.1 2x1.5 sq mm+1x1.5 sqmm earth wire 45 meters 233.00 meter 10485.00 2.2 4x1.5 sq mm+2x1.5 sqmm earth wire 35 meters 326.00 meter 11410.00 2.3 6x1.5 sqmm +3x1.5 sqmm earth wire 22 meters 430.00 meter 9460.00 2.4 2 x 4 sq. mm + 1 x 4 sq. mm earth wire 40 meters 334.00 meter 13360.00 2.5 4 x 4 sq. mm + 2x 4 sq. mm earth wire 30 meters 537.00 meter 16110.00 2.6 2x6 sqmm +1x6sqmm earth wire 5 meters 439.00 meter 2195.00 2.7 4x6 sqmm +2x6sqmm earth wire 5 meters 754.00 meter 3770.00 3 supplying and drawing following sizes of frls pvc insulated copper conductor, single core cable in the existing surface/recessed steel/pvc conduit as required. 3.1 2 x 1.5 sq. mm 15 meters 95.00 meter 1425.00 3.2 3 x 1.5 sq.mm 15 meters 181.00 meter 2715.00 3.3 6 x 1.5 sq.mm 15 meters 285.00 meter 4275.00 3.4 3x 4 sqmm 10 meters 206.00 meter 2060.00 4 supplying and fixing of following sizes of medium class pvc conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit i/c making good the damages up to its original finish as required.(m/s precision make ors.s) 4.1 20 mm 45 meters 128.00 meter 5760.00 4.2 25 mm 45 meters 145.00 meter 6525.00 5 s/f following modular type switch/socket or accessories on the existing switch box/cover i/c connections etc as reqd.(accessories to be used of mk blanze /legrand aretior/anchor vision ) 5.1 5/6 amps switch 10 nos 103.00 each 1030.00 5.2 3 pin 5/6 amps socket 25 nos 122.00 each 3050.00 5.3 15/16 amps switch 6 nos 156.00 each 936.00 5.4 6 pin 15/16 amps socket outlet 2 nos 197.00 each 394.00 5.5 modular blanking plate 5 nos 40.00 each 200.00 5.6 stepped type electronic fan regulator (2m) 7 nos 369.00 each 2583.00 5.7 3.0 mm thick phenolic laminated sheet isi mark. 1000 sq inchs 2.00 sq inch 2000.00 5.8 single information outlet w/o faceplate 5 each 636.00 each 3180.00 5.9 modular indicator red 4 each 91.00 364.00 5.1 25amp ac motor starter 3m 1 each 1005.00 each 1005.00 5.2 2mm thick sheet steel sheet i/c cutting/ drilling holes in required shape and size 500 sq inch 7.00 sq inch 3500.00 5.3 telephone socket outlet 1 nos 109.00 each 109.00 6 supplying and fixing following size modules, gi box (pvc in case of surface) alongwith modular base & cover plate for modular switches in recess etc as required.(accessories to be used of mk blanze /legrand aretior/anchor vision ) 6.1 1 or 2 module (75mmx75mm) 10 nos 298.00 each 2980.00 6.2 3 module (100mmx75mm) 2 nos 327.00 each 654.00 6.3 4 module (125mmx75mm) 1 nos 343.00 each 343.00 6.4 6 module (200mmx75mm) 1 nos 402.00 each 402.00 6.5 8 module (125mmx125mm) / (75mmx225mm) 5 nos 454.00 each 2270.00 6.6 12 module (200mmx150mm) 1 nos 547.00 each 547.00 7 supplying and fixing suitable size gi box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (for light plugs to be used in non residential buildings)..(accessories to be used of mk blanze /legrand aretior/anchor vision ) 3 nos 477.00 each 1431.00 8 supplying and fixing suitable size gi box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connectionetc. as required..(accessories to be used of mk blanze /legrand aretior/anchor vision ) 6 nos 586.00 each 3516.00 9 supplying and drawing following pair 0.5sqmm fr pvc insulated copper conductor, unarmoured telephone cable in the existing surface/recessed steel/pvc conduit etc as reqd(m/s polycabor s.s) 9.1 2 pair 40 meter 38.00 meter 1520.00 10 supplying and fixing metal box of following sizes (n.s) on surface or in recess with suitable size of phenolic laminated sheet cover in the front i/c panting etc as required. 10.1 100mm x 100mm x 60mm 4 nos 209.00 each 836.00 10.2 180mm x 100mm x 60mm 4 nos 245.00 each 980.00 10.3 200mm x 250mm x 60mm 2 nos 468.00 each 936.00 sh ii (fans & fittings) 11 p/f ms fan hook s fabricated out of 12 mm thick round steel bar for installation of ceiling fan i/c cutting the ceiling and repairing the same or if roog is of shade type the fan to be modified as per truss/ structure pipe etc. as required.( in case of new rcc slab casting, agency will provide 150mm dia 16swg ms fan box with 3mm thick phenolic sheet i/d 12mm thick round steel bar for installation of ceiling fan ) 8 nos 273.00 each 2184.00 12 sitc of 1400 mm sweep ceiling fan etc. as reqd. (m/s. cg high speed or equivalent model of orient or havells make) 8 nos 2336.00 each 18688.00 13 sitc of following energy efficient white led fixture/ luminaire etc complete as reqd. 14 sitc of following type ms white powder coated led batten / mounting rail suitable for t5/t8 led lamps having plastic end caps suitable for operation at 230volts 50 hz ac suppy etc as reqd . (make philips tmc 501 p 1xt led 22w p3241 & tmc 501 p 2xt led 22w p3242 /similar superior model of make wipro/ havells/ cg/ jaquar). 14.1 single led lamp 25 nos 615.00 each 15375.00 14.2 double led lamp 4 nos 711.00 each 2844.00 15 supplying and fixing t8 retro led tube 1200mm length having aluminium housing and pc diffuser in the existing t8 fitting suitable for 230volts 50 hz ac suppy complete etc as reqd (make: jaquar ltbl01x020xc /similar superior model of make wipro/ havells/ cg/ philips) 33 nos 404.00 each 13332.00 16 1x9 watt 2 feet led batten having aluminium base and inbuilt driver suitable for operation at 230 volts 50 hz ac supply etc as reqd (wipro /philips /crompton make ) 5 nos 425.00 each 2125.00 17 s/f of 225 mm sweep exhaust fan heavy duty with double ball bearing, 4 blade , with bird guard complete as required. (m/s. m/s cg transair / almonard medium duty, havells ventilair or equivalent model of ss make) 3 each 2388.00 each 7164.00 sh iii (main board and sdb s) 18 s/f following way, single pole and neutral/triple pole and neutral , sheet steel, mcb distribution board, 240 /415volts, on surface/recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc as required. (but without mcb/rccb/isolator) 18.1 2 way enclosure 1 nos 482.00 each 482.00 18.2 6 way, double door 1 nos 2206.00 each 2206.00 18.3 8 way, double door 1 nos 2573.00 each 2573.00 18.4 12way spn double door 1 nos 2315.00 each 2315.00 18.5 4way(4+12), double door 1 nos 4091.00 each 4091.00 19 s/f 5 amps to 32 amps rating, 240/415 volts, c curve, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc as required. 19.1 single pole 30 nos 256.00 each 7680.00 19.2 40 amp double pole 3 nos 920.00 each 2760.00 19.3 40 a fp mcb 2 nos 1910.00 each 3820.00 20 supplying of following size xple insulated pvc outer sheathed aluminium conductor armoured cable confirming to is 7098( part i) /1988 suitable for operation on1.1 kv grade as reqd 20.1 2x6 sqmm 60 meter 103.00 meter 6180.00 20.2 4x16sqmm 30 meter 174.00 meter 5220.00 21 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size direct in ground including excavation and refilling the trench etc. as required, but excluding sand cushioning and protective covering. 21.1 upto 35 sq. mm 20 meter 200 meter 4000.00 22 laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size in the existing rcc/ hume/ metal pipe as required. 22.1 upto 35 sq. mm 20 meter 37 meter 740.00 22 laying and fixing of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size on wall surface as required. 22.1 upto 35 sq. mm 50 meter 55 meter 2750.00 23 supplying and making end termination with brass compression gland and aluminium lugs for following size of pvc insulated and pvc sheathed / xlpe aluminium conductor cable of 1.1 kv grade as required. 23.1 2x6 sqmm 8 sets 240 set 1920.00 23.2 4x16sq. mm (28 mm) 6 sets 309 set 1854.00 24 supplying and fabricating of 16 swg ms sheet i/c cutting, bending, drilling ,welding powder painting etc as reqd 1 sqm 1200 sqm 1200.00 sh iv ( earthing) 25 earthing with g.i. earth plate 600 mm x 600 mm x 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. 3 sets 7472 set 22416.00 26 providing and fixing 25 mm x 5 mm g.i. strip in 40 mm dia g.i. pipe from earth electrode including connection with g.i. nut, bolt, spring, washer excavation and re filling etc. as required. 30 meter 706 meter 21180.00 27 providing and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required. 30 meter 244 meter 7320.00 28 providing and fixing 8 swg dia g.i. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. 200 meter 21 meter 4200.00 29 supplying and fixing 50mm x 5 mm thick gi earth bar of 300mm long with two nos insulation drum and 8 nos hole in earth bar etc complete as required nos 280 each 30 sitc of 63 amp on load change over switch in sheet steel enclouser suitable for operattion at 415 volts 50 hz ac supply etc as reqd( l&t make model no co10630osoo or s.s) 1 nos 7628 each 7628.00 31 sitc of 63 amp tpn sdfu (main switch) with suitable hrc fuse suitable for operation 415 volts 50 hz ac supply etc as reqd (l&t make fn 63 tpn / fp ce* or s.s) 1 nos 6148 each 6148.00 32 providing and fixing (isi marked)(is:2878)portable fire extinguiser ,carbon di oxide (co2) type flat base including valve , discharge hose pipe of not less than10mm zdia and 1.0 mlongand omplete in all respect including initial refilling with co2 gas onfirming to is:307 1966 filled to filling ratio not more than 0.667 and wall suspension bracket etc as reqd ( safex/kanex/fire fite) 32.1 4.50 kg capacity 2 nos 6200 each 12400.00 sh v ( lan wiring) & cctv 33 supplying and drawing of utp 4 pair cat 6 lan cable in the existing surface/ recessed steel/ pvc conduit as required. 33.1 1 run of cable 25 meter 57 meter 1425.00 33.2 2 run of cable 20 meter 96 meter 1920.00 33.3 3 run of cable 25 meter 134 meter 3350.00 34 supply of following equipments/accessories for local area networking of computers through database servers complete as reqd(m/s d link/ss make) 34.1 patch cord cat 6 ( factory crimped 2 mtr) 4 nos 267 each 1068.00 35 s/f cable management system of following size with accessories as reqd on surface as reqd (m/spresicion/ mk make) 35.1 32mm x 12.5mm 3 meters 74 meter 222.00 35.2 50mm x 50mm 3 meters 241 meter 723.00 36 s/f wall mount 19 12u rack having 600 mm depth along with all accessories, etc as reqd (for networking/ dvr/ dvr smps) 1 nos. 7,720 each 7720.00 sh vii ( compound light & misc 37 sitc of 25watt led type street light fitting ( ip 65 protection)made of diecast aluminim housing with corrosion resistance polycarbonate cover, electronic driver having efficacy of 100lm/wat , cct 5700k i/c p/f 1.2 meter long 32mm dia gi/ ms bracket (welding directly to c/l pole with 6mm ms sheet as support in case of fixing on pole) with two coats red oxide and two coats of white enammelled synthetic painting , etc as reqd(m/s philips greenline smart brp042 25led hp/cw 240v / crompton greaves as per direction of engineer in charge ) 5 nos 3682 each 18410.00 38 s/f weather proof front operated pvc box m/s syntex of aprx size 230mm x170mmx105mm deep with locking arrangement & 4 way backelite connector with 1 no 1amp sp mcb i/c connection with 3 core 1.5sqmm pvc insulated pvc sheathed copper conductor cable upto fitting i/c testing , sign writing etc as reqd. 5 nos 950 each 4750.00 39 sitc of 1.0hp/0.75kw, single phase phase open well submercible pump set,capable to discharge 120lpm to 290lpm at head range 22.0 14.0 mtr. head having 2800 rpm with control panel of the pump with 5.0 m long power chord and footvalve bend and stainer i/c connnection etc comp as reqd.(model no.lubi lhl151* make or similar capacity of /kirloskar kos135i or ss make) 1 nos 13972 each 13972.00 40 s/f 3x2.5 sqmm pvc insulated pvc sheathed copper conductor flat submersible cable suitable for 415volt 50hz ac supply etc as reqd. (m/spolycab) 25 meter 137 meter 3425.00 41 s/f following accessories for pump set i/c making proper connection for delivery / suction/control etc as reqd ( isi make) 41.1 25 mm cpvc ball valve 1 nos 434 nos 434.00 41.2 25 mm cpvc pipe sdr 11 with all required accessories 25 meter 397 meter 9925.00 42 providing, laying and fixing following dia g.i. pipe (medium class) in ground/ roof complete with g.i. fittings including trenching (75 cm deep)and re filling, if laid in ground or providing clamps if fixed in between wall for fixing cable trays / fans etc as reqd etc as required 42.1 40mm dia 10 meter 428 meter 4280.00 ...

Northern Coalfields Limited - Madhya Pradesh

38692206 bids are invited for 1 excavation of pole pit 2 excavation of stay pit 3 fixing of disc insulator 4 fixing of post insulator 5 laying of dog conductor 6 laying of earth wire 7 fabrication of ms channel 8 dismantling of rail pole 9 dismantling of stay rod 10 dismantling overhead line 11 fabrication of pathway 12 laying of ht cable 13 earthing with gi earth pipe 14 painting with aluminium paint 15 supply and fixing of triple pole 16 supply of stay assembly 17 supply of gi earth wire 18 supply of hard ware total quantity : 323058...

Northern Coalfields Limited - Madhya Pradesh

38692145 bids are invited for 1 excavation of pole pit 2 excavation of stay pit 3 fixing of 11 / 22 kv disc insulator 4 fixing of 11 / 22 kv pin / post insulator 5 laying of dog conductor 6 laying of earth wire 7 fabrication of ms channel 8 dismantling of rail pole 9 dismantling of overhead line disc insulator 10 supply of gi earth wire 7 / 14 swg 11 supply of bolts ms black 12 supply of hard ware wolf conductor 13 supply of stay assembly 14 supply of disc insulator 15 painting with aluminium paint total quantity : 16122...

Madhya Pradesh Power Transmission Company Limited - Madhya Pradesh

37727902 tender for modification/shifting of various 400/220/132kv ehv lines due to construction of road/railway/bridge/canal etc., restoration of supply in case of tower collapse/damaged due to heavy wind/cyclone/flood or any other reason, replacement of towers due to rusting, deterioration of tower parts by carrying out various activities like repairing of stubs/chimney which involves excavation around the chimney, breaking of chimney, repairing of damaged stub by cutting and jointing stub as per requirement, placing a new angle, fixing cleat plates, painting with anti corrosive paint, recasting of chimney, muffing, coping and backfilling where 1/2/3/4 no. stub is to be repaired, tower erection and associated dismantling of towers, de stringing and stringing of conductor and earth wire/opgw in central zone of mp...

Western Coalfields Limited - Madhya Pradesh

37667580 tender for maintenance of overhead line 11 kv intake well and 33 kv main substation pathakhera to chattarpur i mine. 1 42.8 supplying and drawing guard wire / earth wire / bearer wire 13 sq mm ( 4mm. dia ) g.i. including stringing, binding at existing insulators or brackets, jointing, jumpering, connecting & cradle etc. as required and clearing of obstacles ( if any ) 2 km 2 42.19 erection of rs joist pole / h beam / steel tubular / steel rail pole of length exceeding 10 metres but not exceeding 13 metres in cement concrete m 10 ( 1 cement:3 core sand: 6 graded stone aggregate 40mm nominal size ) base, foundation, muffing including excavation and back refilling etc. 5 each 3 ( a ) 42.42 labour charges for erection of angle / channel / flat iron fitting for overhead line & sub station etc such as d bracket, cross arms, top clamp, v cross arms, back / support clamp or other similar work etc. including nut bolts of required size, 80 kg 3 ( b ) 42.45 supplying and erection of 33kv porcelain pin insulator complete with long steel head g.i. pin, nut, washer etc. as required 7 each 4 42.47 supplying and erection of a set of four 11kv porcelain disc insulators for 33kv overhead lines with galvanized insulator fittings, ball and socket type, and complete with galvanized strain clamp, bolts, nuts, washers etc. 10 each 4 ( a ) 42.48 labour for erection of 11 / 33kv porcelain pin insulator complete with hardware 10 each 5 42.5 labour for erection of a set of three / four 11kv porcelain disc insulators for 33kv overhead lines complete with hardware 15 each 5 ( a ) 42.53 supplying and erection of 33kv ( 10 kn ) polymer pin insulator complete with long steel head g.i. pin, nut, washer etc. 5 each 5 ( b ) 42.54 supplying and erection of 33kv ( 45 kn ) polymer disc insulators for 33kv overhead lines with galvanized insulator fittings, ball and socket type, and complete with galvanized strain clamp, bolts, nuts, washers etc. 5 each 6 42.61 supplying installing, testing & commissioning of outdoor h.t., ab switch assembly set gang operated with brass contact parts, including required gi pipe operating rod, handle & locking arrangement on on off position conforming to is complete with required material and installing on existing dp structure to complete the job as required as per specification. ( set of 3 nos. ) 6 ( a ) 42.61.1 11 kv, 400amp 2 set 6 ( b ) 42.61.2 33kv, 600amp 2 set 7 42.62 supplying installing, testing & commissioning d.o. fuse assembly with brass part contact for 33 or 11 / 0.4 kv dp structure set of 3 nos. with fuse barrel i / c required fuse element & other materials as per specification on existing d.p. structure as required. 7 ( a ) 42.62.1 11kv 2 set 7 ( b ) 42.62.2 33kv 2 set 8 42.63 supplying & replacement of d.o. fuse barrel with brass parts for 33 or 11 kv i / c required fuse element according to load as per specification on existing d.p. structure as required. 8 ( a ) 42.63.1 11kv 1 set 8 ( b ) 42.63.2 33kv 2 set 9 total ( exclusive of gst as per applicable ) ...

Madhya Pradesh Power Transmission Company Limited - Madhya Pradesh

36850321 ext: tender for for modification/shifting of various 400/220/132kv ehv lines due to construction of road/railway/bridge/canal etc., restoration of supply in case of tower collapse/damaged due to heavy wind/cyclone/flood or any other reason, replacement of towers due to rusting, deterioration of tower parts by carrying out various activities like repairing of stubs/chimney which involves excavation around the chimney, breaking of chimney, repairing of damaged stub by cutting and jointing stub as per requirement, placing a new angle, fixing cleat plates, painting with anti corrosive paint, recasting of chimney, muffing, coping and backfilling where 1/2/3/4 no. stub is to be repaired, tower erection and associated dismantling of towers, de stringing and stringing of conductor and earth wire/opgw in west zone of mp...

Madhya Pradesh Power Transmission Company Limited - Madhya Pradesh

36320435 tender for extension of construction of road, railways, bridge, canal etc., restroation of supply in case of tower collapse / damaged due to heavy wind cyclone / flood or any other reason, replacement of towers due to rusting, deterioration of tower parts by carrying out various activities like repairing of stubs/chimney which involves excavation around the chimney, breaking of chimney, repairing of damaged stub by cutting and jointing stub as per requirement, placing a new angle, fixing cleat plates, painting with anti corrosive paint, recasting of chimney, muffing, coping and backfilling where 1/2/3/4 no. stub is to be repaired, tower erection and associated dismantling of towers, de stringing and stringing of conductor and earth wire/opgw in west zone of mp...

Council Of Scientific And Industrial Research - Madhya Pradesh

35783899 tender for extension of jigyasa project at ampri, bhopal 1 earth work in surface excavation not exceeding 30 cm in depth butexceeding 1.5 m in width as well as 10 sqm on plan including gettingout and disposal of excavated earth upto 50 m and lift upto 1.5 m, asdirected by engineer in charge: 1.01 all kinds of soil 2 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer in charge. all kinds of soil. 3 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level :1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 40 mm nominal size ) 4 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level :1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) incuding manufactured sand derived from recycled concrete aggregate ( rca ) upto 20% : 3 graded stone aggregate 20 mm nominal size of recycled concrete aggregate ( rca ) upto 20%. 5 reinforced cement concrete work in walls ( any thickness ) , including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 ( 1 cement : 1.5 coarse sand incuding manufactured sand derived from recycled concrete aggregate ( rca ) upto 20% : 3 graded stone aggregate 20 mm nominal size recycled concrete aggregate ( rca ) upto 20% 6 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral staircases above plinth level up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 ( 1 cement : 1.5 coarse sand incuding manufactured sand derived from recycled concrete aggregate ( rca ) upto 20%: 3 graded stone aggregate 20 mm nominal size recycled concrete aggregate ( rca ) upto 20% ) 7 centering and shuttering including strutting, propping etc. and removal of form work for :foundations, footings, bases of columns, etc. for mass concrete 8 centering and shuttering including strutting, propping etc. and removal of form work for walls ( any thickness ) including attached pilasters, butteresses, plinth and string courses etc. 9 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform 10 centering and shuttering including strutting, propping etc. and removal of form for : lintels, beams, plinth beams, girders, bressumers and cantilevers 11 centering and shuttering including strutting, propping etc. and removal of form for :columns, pillars, piers, abutments, posts and struts 12 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. thermo mechanically treated bars of grade fe 500 d or more. 13 providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, ( i ) single socketed pipes 110 mm diameter 14 providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion. 12.42.1 coupler 12.42.1.2 110 mm 15 providing and fixing on wall face unplasticised pvc moulded fittings / accessories for unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion. single tee with door 110x110x110 mm 16 12 mm cement plaster of mix :1:4 ( 1 cement: 4 sand ) 17 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand ) finished with a top layer 6 mm thick cement plaster 1:6 ( 1 cement : 6 fine sand ) . 18 applying priming coat:with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron / steel works 19 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 20 providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 21 wall painting with premium acrylic emulsion paint of interior grade ( plastic paint ) , having voc ( volatile organic compound ) content less than 50 grams / litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.and colour. two or coats. 22 applying priming coats with primer of approved brand and manufacture, having low voc ( volatile organic compound ) content. with water thinnable cement primer on wall surface having voc content less than 50 grams / litre. 23 structural steel work in providing and fixing ms grill in windows in position and applying a priming coat of approved steel primer and two coat of oil paint all complete as direction of e in c 24 supplying and filling moorum / kopra, base of floor / rooad etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by vibratory roller and watering, levelling etc complete 25 brick work with chimny brick of ravi / kavi / shree / a d in superstructure above plinth level upto floor v level in all shapes and sizes in : cement mortar 1:4 ( 1 cement : 4 coarse sand ) 26 providing and applying multicoat synthetic plaster as per approved design, pattern texture in 2 mm thick on new plastered surface finished in proper line and level as directed by engineer in charge in five coats consisting of composition of four order of application given as under includig all materials, labour and scaffoldings etc. 1 ) scrapping of the new surface and applying sealer primer mixed with water in the ratio 1:3 ( part sealer primer : 3 part water ) and applying by brush @ 0.25 kg / sqm. 2 ) applying levelling coat of spectrum rustic fine or equivalent with trwel as a putty finished to generate required texture by trowel. 3 ) applying third coat of synthetic plaster with trwel @ 2.5 kg / sqm finished to generate required texture by trwel. 4 ) applying two coats of exterior super fine pigmented acrylic wall coating as top coat @ 0.5 kg / sqm in two coats and colours as approved by engineer in charge all up to a height of 10m. 27 providing and laying vitrified tiles in floor and skirting different sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) jointing with grey cement slurry @ 3.3kg / sqm including grouting the joints with white cement and matching pigments etc., complete. size of tile 600x600 mm 28 grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade ( 0.10 kg of hardener and 0.20 kg of resin per kg ) , including filling / grouting and finishing complete as per direction of engineer in charge.size of tile 600x600 29 providing and fixing flush doors 30 mm thick isi mark with decorative lamination 0.75 mm thick on both sides including teak wood beading on edeges including l drop ss fiitings 10 & tower bolts 6 , isi marked heavy door closer etc complete as per e in c 30 labour for shifting of machines, jungle clearance, junk clearance, septic tank & reconnection of tank etc 31 p / f glazed aluminium powder coated section in windows and ventilators including all fittings and fixtures as per e in c 32 providing and fixing roller blind of approved make design in window of required size in approved pattern and design as directed by e in c 33 providing and fixing granite in window sill and counter platform and steps / ramp in cm 1:4 including nosing, grinding, polishing etc complete as per site requirement and direction of e in c 34 p / f ss railing in 2 dia pipe ht = 30 including all fittings and fixtures as per e in c 35 p / f 60 mm thick m 30 grade rubber moulded paver block laid on 50 mm thick stone dust with filling gaps with sand and locking edeges with concrete completes as per e in c 36 wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm frls pvc insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with modular switch, modular plate, suitable gi box / celling rose and earthing the point with 1.5 sq.mm. frls pvc insulated copper conductor single core cable etc as required.group c. 37 wiring for circuit / submain wiring alongwith earth wire with the following size of frls pvc insulated copper conductor, single core cable in surface / recessed pvc conduit as required 37.01 2 x 1.5 sq.mm + 1 x 1.5 sq.mm earth wire. 37.02 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire. 37.03 2 x 4 sq.mm + 1 x 4 sq.mm earth wire. 37.04 2 x 6 sq.mm + 1 x 6 sq.mm earth wire.. 38 supplying and drawing following 2 pair 0.5 mm dia frls pvc insulated annealed copper conductor telephone cable in the existing surface / rrecess / steel / pvc conduit as required 39 supplying and fixing of following sizes of medium class pvc conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required. 39.01 20mm 39.02 25mm 40 supplying and fixing follwing modular switch / socket on the exixting modular plate & switch box including connections excluding moddular plate etc as required. 40.01 5 / 6amps switch 40.02 3 pin 5 / 6 amps socket outlet 40.03 15 / 16 a switch 40.04 6 pin 15 / 16 a socket outlet 40.05 telephone socket outlet 41 supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including, connections but excluding modular plate etc. as required. 42 supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. 43 supplyiong and fixing following size / modular plate, gi box alongwith modular base & cover plate for modular switchesin recess ets as required 43.01 1 / 2 module 43.02 6 module 43.03 8 module 44 installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length ( upto 30 cm ) with 1.5 sq. mm frls pvc insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 45 supplying and drawing of utp 4 pair cat 6 cable in the executing surface recssed / steel / pvc conduit, as required 45.01 2 run of cable 46 supplying & fixing suitable size gi box wih modular plate and cover in front on surface or in recess including providing and fixing 25 a modular socket outlet and 25 a modular sp mcb, c curve including connections, painting etc. as required. 47 supplying and fixing following way, single pole and neutral, sheet steel, mcb distribution board, 240 v, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. ( but without mcb / rccb / isolator ) 47.01 12 way double door 48 supplying and fixing 5 amps to 32 amps rating, 240 volts c series, miniature circuit breaker suitable for inductive load of following poles in the existing mcb db complete with connections, testing and commissioning etc. as required. 48.01 single pole 48.02 single pole and neutral 49 supplying, installation, testing and commissioning of prewired led compact light fitting of following type complete with all accessories etc. recess / surface / panel / flase ceiling i / c connection with 3 x 1.5 sq. mm frls pvc insulated copper conductor wire earthing etc. as reqd. 49.01 supplying and fixing of led surface mounted downlight 15 / 18 watt with lamp complete with connection and testing etc as required as per havells modal no.glowgenxdls18wled857s or similar make like ( havells / crompton / philips / wipro ) 50 supply, installation, testing and commissioning of 1200 mm sweep, bee 5 star rated, ceiling fan with brush less direct current ( bldc ) motor, class of insulation: b, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, power factornot less than 0.9, service value ( cm / m / w ) minimum 6.00, air deliveryminimum 210 cum / min , 350 rpm ( tolerance as per is : 374 2019 ) , thd less than 10%, remote or electronic regulator unit for speedcontrol and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree c ( max. ) , insulation resistance more than 2 mega ohm, suitable for 230 v, 50 hz, single phase acsupply, earthing etc. complete as required. 51 supplying and fixing of rj 45 computer socket outlet modular type with gio box and modular plate i / c making connection etc. as reqd. 52 sitc of invertor type split air conditioing, minimum 3 star rating , rotary type campressure , 1.5 ton capacity , 100 % copper , input voltage 230 volt, eco friendly gas swith outdoor stand and complete installataion, with fixing of celling with anchor fasner bolts, laying of copper wire etc as required ( carrier / hithachi / blue star / daikin ) ...

Military Engineer Services - Madhya Pradesh

35563767 special repair to building no p 50 bls at afs amla , taking down, cement plaster of any description from brick or stone walls etc, including raking out joints, hacking for key scrubbing down with water etc and disposing of the rubbish materials in low lying areas of defence land all as specified and as directed. , demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles etc complete all as specified and as directed. , m&l for brickwork with fly ash ,subclass ‘b’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6all as specified and as directed. , m&l 15mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:4 finished fair andevenwithout using extra cement complete all as specified and as directed. , m & l for 10 mm thick rendering in 1:6 cm on wall of fair faces brick & concrete surfaces finished even and smooth without using extra cement complete all as specified. , m&l for 1 to 2mm thick wall care putty on wall surfaces smooth finish complete all as specified and directed by engineer in charge , m & l 5mm thick rendering in 1:3 cm on ceiling, rcc facia and chajjas of fair faces of brick or concrete surfaces finished even and smooth without using extra cement complete all as spd and directed. , m&l for preparing new surfaces of walls and applying two coat of cement base paint over a coat of primer complete all as specified and directed. , m&l two coats of oil bound distemper on wall newly plasterd surfaces over a coat of alkali resistant primer complete includingprepatation of new surfaces complete all as specified and directed. , m&l three coats of white washon newly surface on ceiling including all preparation complete all as specified & directed , material & labour for cleaning of roof surfaces and applying a coat of oil base bituminous primer @ 0.30 lit per sqm over andincluding 15mm thick cement plaster in cm 1:4 mix with liquid water proofing admixture@200ml per bag of cement including laying of app based polymeric membrane weighing not less than 3.00 kg/ sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt,not less than 150gms/sq. m) land on primed surface by tension application with 100mm over lap travers and 150mm over lap longitunaland finishing the top surface by applying two coat of aluminium paint @ 0.1kg/sqm on each coat including taking down old treatment complete all as specified and directed. , supply only liquid water proofing chemical all as specified and as directed , dismantling of wall, display board/ceiling board fiber, pulp insulation etc., or insulation board/slab/wool of any thickness including cover fillets complete all as specified and directed by engineer in charge. , s & f size of grid 605 x 605mm anodised aluminium snap grid frame work for false ceiling with hangers 6 mm dia. g.i. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of g.i. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed by engineer in charge. , m & l for 4mm non asbestos fiber cement building boards fixed in cement ceiling flat or sloping to gi/aluminium framework with screws complete all as specified and directed by engineer in charge. , taking down chowkat or frames,area exc 1.5 sqm but not exc 4 sqm each with shutter (without taking off shutters from the frames)complete all as specified and directed . , taking down chowkhats or frames, area not exc 1.5 sqm with shutters (without taking off shutters from the frames)complete all as specified and directed , powder coated aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by engineer in charge. , providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber/ neoprene gasket required (fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, c.p. brass/ stainless steel screws all complete all as specified and directed by engineer in charge. , s&f 5.5 mm thick sheet glass, selected quality and glazing with oil putty in squares n exc 0.5 sq. m in each pane of aluminium door/window complete all as specified and directed by engineer in charge , m & l 12mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed in aluminium frame with necessary beading complete all as specified and directed by engineer in charge. , s & f double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by engineer in charge. , s & f floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified and directed by engineer in charge. , s & f 4 lever aluminium mortice lock, vertical type, size 100 mm complete all as specified and directed by engineer in charge. , s&f 100mm size aluminium anodized butt hinges complete all as specified and directed by engineer in charge. , s&f 75mm size aluminium anodized butt hinges complete all as specified and directed by engineer in charge. , s & f for 200mm long barrel tower bolt aluminium anodized with staples and bolt of extruded section complete all as specified and as directed. , s&f 150mm long size extruded aluminium alloy handles, cast type anodised complete as specified. , s& f 150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified , s&f 100mm long size extruded aluminium alloy handles, cast type anodised complete as specified. , s&f door closer hydraulically regulated designation no.2 universal type,suitable for door shutters of 701 to 850 mm width and of wt 36 to 60 kg. aluminium (die cast) complete all as specified & directed. , dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by engineer in charge. , m&l for joint free non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match set,over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete of item all as directed. , m&l for non skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in coloured cement to match of lighter shade of tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete of item all as directed. , ditto all as per item no. 34 but in vertical surfaces, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 10mm thick rendering or backing coat in cement mortar 1:4 complete of item all as directed. , material & labour for light shade vitrified ceramic tiles 10 mmthick (square /rectangular) polished area of each tiles not exceeding 0.36 sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cm 1:6 complete all as specified and directed. , ditto all as per item no 36 but in vertical surface as in skirting, set and jointed in neat cement, slurry & pointed in coloured cement to match the shade of tiles over and including 10mm thick rendering or backing coat in cement mortar 1:4 complete all as specified and directed by engineer in charge. , m&l for digital glazed ceramic tiles in vertical surfaces 450 x 300 x 7 mm thick,etc set and jointed in neat cement slurry and pointedin coloured cementto match the shade of tiles including 10mm thick backing coat in 1:4 cement mortor complete all as specified and directed. , m & l for coloured glossy heavy duty endura flooring tiles of size 30cm x 30cm x 10 mm set with grey cement and no pigment, jointed ad pointed in neat cement slurry in floors over and including 15mm thick screed bed in cm 1:6 complete all as specified and directed by engineer in charge. , supply & fixing in repair vitreous china squatting pan, orissa patteren, size 580 x 440 mm white, with integral footrests (excluding flushing cisteren and flush pipe) complete all as specified and directed. , s&f in repair vitreous china wash down water closet pan (pedestal pattern) white,incl. trap, connection to drain and flushing pipe including seat cover for pedstal pan complete all as specified and directed. , s&f pvc(swr) 110mm dia s trap including connecting to out let with solvent cement complete all as specified and directed. , m & l in repairs for pvc nahani trap, plain with grating including jointing to waste pipe fixed in cement concrete type b 1 (1:2:4) with solvent cement of dia 75mm complete all as specified and directed. , s&f in repair10 litre capacity pvc valveless syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including bracketscomplete all as specified and directed. , s&f in repairs pvc connections 15mm size with ptmt nuts of length 450mm fixed to pipes and valves complete all as specified and directed. , s&f in repairs wash basins, vitreous china (flat back or angle back type) any size size 550mmx400mm, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply incl taps waste chain and plug and brecketswaste coupling brass cp 32 mm bore with long screwed shanksbedded in red lead cement and other end fixed and pillar taps 15 mm bore cast copper alloy fancy type chromium plated screwed down high pressure withlong screwed shanks screwedand removing debris out of mod land all as specified and directed. , taking down gi tubing 15mm bore all as specified and directed by engineer in charge. , s&f gi tubing 15mm bore medium gradewith all fittings fixed to wall and ceilingcomplete all as specified and directed. , s&f in repairs 15 mm bore bib taps cast copper alloy with chromium platedcrutch or butterfly handle scrwed, screwed for iron pipe or for brass ferruleand fixed complete all as specified.. , s & f in repair 15mm bore stop valveschromium plated screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions fixed complete all as specified and directed , s&f in repairs of 600x450mm size bevelled edge mirror of selected quality glass 6mm thick mounted on any type of wall including polishingand fixed on wall withchromium plated studds and cup washers complete all as specified and directed. , s&f in repairs ss tubular towel rail ,d type 60 cm long between two flanges fixed on wall with studds complete all as specified and directed. , s&f in repair ss towel ring of ptmt fixed with and including chromium plated brass screws and wooden/ plastic cleats (minimum weight 90gms) complete all as specified and directed. , s&f sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long , s&f in repair 15 mm stainless steel health faucet with 1.5 mtr long ss pipe and holder ,fixed to wall with screws and connection with pipe complete all as specified and directed. , dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by engineer in charge. , s&f framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to fe.290.gde e 165 , s & f factory made steel window with side hung shutters incl boxtype hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as specified and as directed by engineer in charge. (as per td drawings ce (af)/ngp/2003/td/08 sheet 1/12 to 12/12 , s & f steel window with side hung shutters incl boxtype hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded all as specified and as directed by engineer in charge. (as per td drawings ce (af)/ngp/2003/td/08 sheet 1/12 to 12/12 , s & f steel ventilator with top hung shutters inclhinges with steel peg stay, complete all as specified and as directed by engineer in charge , s&fstainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. , m&l for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc. 0.5 sqm in each pane complete all as specified and as directed , cutting holes in brick walls built in cement mortar for inserting hold fast and making good dismantled portion in cement concrete 1:2:4 type b 1, depth exceeding half brick but n. exc one brick complete all as specified , hacking out broken glass (any thickness, size quality or description ) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads all as specified and as directed. , roof trusses (framed), trusses, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, afe 290 (gde e 165)) quality b channel or flat sections) including distance pieces cleats etc., complete all as specified and directed by engineer in charge. , preparation new painted steel surfaces of any description over 10cm width or grith not otherwise described and applying two coat of synthetic enamel paint over one coat of red oxide and zinc chrome complete all as specified and as directed , dismantling of asbestos cement/gi corrugated or semi corrugated sheets as in roof covering all as directed. , s&f pre painted galvalume aluminum zinc coating gi based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. , s&f pre painted galvalume aluminum zinc coating gi based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. , demolition of cement concrete ( unreinforced) as in ground floor and paving not exc 15 cm thickness below or above gl , m&l for 75 mm thick pcc 1:3:6 type b i (40mm graded aggregate ), as in plinth protectioncomplete all as directed. , m&l pcc 1:4:8 type d2 75mm thick as in sub base comlete all as pecified and directed complete. , m&l for 100 mm thick pcc 1:2:4 type b 1 (40 mm graded aggregate), as in top layer including spike rolling to surface or making impressions of expanded metal, whilst the concrete is green complete all as directed. , m&l for preparation of old painted wooden surfaces of any description, over 10cm in width or girth,not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed. , m&l for preparation of old painted steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coat of synthetic enamel paint complete all as specified and directed. , dismantling water tanks ,exc 250ltr but not exc 500 ltr and removing to store complete all as specified and directed. , s&f rotational moulded polyethylene water storage tanks of capacity 500ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specified in ssr part i , m& l for complete removal of existing treatmentof old internal surfacesapply two coat of oil emulsion distemper on wall surfaces over a coat of chalk white primer including wall care putty making smooth finish surface and complete preparaton of new surface complete all as specified and directed. , m& l for complete removal of existing treatmentof old external decorative surface of walls and applying two coat of cement base paint,over a coat of cement primer includingcracks filling with exterior wall care puttywhere ever necessary and as specified and directed. , m& l for preparing of old decorative surface ofceilings and applying one coat of white wash on ceilng including cornices etc complete with cracks filling with wall care putty where ever necessary and as specified and directed. , taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittingsand fixturesuch as switches, ceiling rose, light fittings etc & making good the surface on wall complete. , m&l for point wiring using approved colour coding as per is with 1.5 sq. mm two single core pvc insulated but unsheathedfr cable, 1100 volts grade, isi 694 marked with multistranded copper conductor and earth continuity wire with similar 1.5 sqmm cable (including connecting to earth dolly) drawn through isi marked heavy duty rigid pvc concealed conduit with all accessories etc with mild steel sunken box 50mm deep 1.6mm thick with earth dollyduly, concealed in the wall and havingmodular cover plate with a frame suitable for modular switch/ sockets/ regulators for the following: , one light point controlled by one switch one way. , onefan point controlled by one switch one way. , one 3 pin 5 amps socket outlet point controlled by one switch one way on same board. , one 3 pin 5 amps socket outlet point controlled by one switch one way on independent board. , all as per item no : 82point wiring with 2.5 sqmmsingle core coppercable and earth continuity wire with 2.5 sqmm single core cable for one three pin 15 amp socket outlet point on independent board. , s & f modular switch 01 way 06 amp, 01 module complete , s & f modular switch 01 way 16 amp, 01 module complete , s & f modular socket6 amp, 2/3 pin combined 2 module complete , s & f modular socket6 /16 amp, 2/3 pin combined 2 in 01, 02 modulecomplete , m & l replacment modular step fan regulator 120 watt 2 module suitable for 230 volt 50 hz supply all as specified , s & f ceiling rose surface bakelite 3 terminals 65 x 50mm, 230 v including pvc box of size 3x 3 round type , s & f in repair for wall mounted led 18/20w crca fitting 230 v with extruded aluminum heat sink provided for efficient heat dissipation and integral electronic driver connector block etc complete with all accessories internally prewired including necessary mounting arrangement, provision of new 2 core multi stranded copper conductor of size 0.5sqmm from ceiling rose to fitting including necessary polycarbonate led tube 4 feet, 18/20 w complete all as specified and directed. , s&f decorative recess mounted luminaire 34/36 watt led suitable for 600mm x 600 mm recess which provides glare free cool white symmetrical illumination and having integral electric driver connector block etc., complete & necessary mounting arrangement, provision of 2 core 0.5 sqmm multistranded copper conductor from ceiling rose to fitting complete all as specfiied and directed. , s&f for suspended type 4ft 36/40 w led fittings linear in sleek design 230 v with integral electronic driver connector block etc., complete with all accessories internally prewired including necessary mounting arrangement, provision of 2 core 0.5 sqmm multistranded copper conductir from ceiling rose to fitting complete as specified and directed. , s&f for envirinment friendly high efficiency with better thermal management type building security light 35/36 watt with integral electric driver connector block etc., complete with all accessories internally prewired including necessary mounting arrangement, provision of 2 core 1 sqmm multistranded copper conductor from ceiling rose fitting complete all as specified and directed. , taking down ceiling fans of any size/sweep after disconnecting the wire from existing ceiling rose and refixing the same after cleaning dust, oiling, greasing including providing flexible cable from ceiling rose to connector of fan complete all as directed by engineer in charge. , s&f for mcb db tpn 4 way double door sheet metal enclosure comprising of oem/manufacturerspecified bus bar 415 volts, 50 hz bus bar and neutral link complete including inserting in wall complete all as specified. , s&f for mcb triple pole and neutral 415 volts, 63 amps, 10 ka. , s & f for ‘c’ curve mcb single pole & neutral 240volts 40 amps , s & f ‘c’ curve mcb sp 240 volt 6 to 30 amp , m & l for flame proof point wiring using approved colour coding as per is with 1.5 sqmm two nos single core pvc insulated but unsheathedfrls cable, 1100 volts grade, isi 694 markedwith multistranded copper conductor and earth continuity wire with similar 1.5 sqmm cable (including connecting to earth dolly) drawn through heavy duty isi markederw stove enamelled, steel conduit concealed in wall suitable for flame proof wiring, not less than 20mm dia with and including flame proof bends and elbows, couplers, bell mouth reducer , junction box all as per relevant is and type tested/ approved by cmri dhanbad all as specified forone light point /power point/ fan point controlled by one no. flp rotatory switch complete al as specified and directed by engr in charge. , s&f in repair new flame proof and wheather proof switch rotary type with termination box in lm6, 16a, single pole 250v suitable for hazardous locations of zone 1 & 2, ex d with relevant is & ip65 protection complete all as specified and as directed. , s&f in repair flameproof switch socket & plug combined in lm6 cable termination box in lm6, 16a,250v, 2p+earth for connection of 3 phase 415v rating equipment suitable upto 10 hp power connection complete all as specified and directed. , s&f cmri certified led flame proof 2x16/20w tube light fixture, recommended for ammunition shed, ip 65 protection complete with all accessories internally pre wired complete all as specified and directed make: crompton greave cat no. extn2lt8 16/20 or equivalent in sudhir/shyam/shakti. , m&l for plate earthingwith galvanisedmild steel plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground vertically (in earth pit not less than2.25 m below normal ground level) with the top edge of the earth plate at a depth not less than 1.5 m below normal ground level,the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides and incl gi earth wirte 4 mm dia bolted (with gi nuts, bolts & check nuts) and riveted to earth plate at one end and connected to metallic bodies of equipment’s etc at the other endincluding 15 mm gi lightgrade protection pipe with allfittings from top of electrode to body of equipment fixed withiron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore gi pipe medium grade from bottom of earth pit to top of electrode complete with earth pit in pcc 1:2:4 type b 2 using 12 mm graded crushed stone aggregate and rcccover complete all specified and shown in electrical plate no 3 of ssr part 1 including testing earth resistance and submitting test report to age e/m by the contractor complete all as specified & directed. note : (i) earthing resistance required in earthing shall less than 3.0 ohms after completion of work. all earthing shall be tested by the contractor in presence of engr in charge.test result shall be recorded and signed by the contractor and engr – in charge.if contractor fail to achieve the above result the same shall be rectified by the contractor without any extra cost to govt.the earthing result will be required maintaining up to end of defect liability period of one year and if any variation found in earthing result during defect liability period same will be intimated to the contractor by engg in charge and contractor shall rectify the same. the quoted rates shall be deemed to include for above said provision. (ii) quoted rates shall be deemed to be included for earth wire with 15 mm dia protection pipe up to 7.5 length. , note: the amount against the schedule of credit mentioned in the tender document shall be deducted from the total amount quoted against sch a while deriving the contract sum for acceptance....

Military Engineer Services - Madhya Pradesh

35548927 tender for provision of certain rw, mw and lbw under ge ( awc ) mhow. exavation in post hole or smilar hoels each n exe 0.5 cum, getting out removing surplus soil to a distance n exe 50 m, complete all as specified and directed. 2 surface excavation n. exc 30 cm deep and averaging 15cm deep and getting out in any type soil, complete all as specified directed. 3 m & l for brick work with fly ash bricks, modular brick, straight or curved on plan exc 6 m mean radius, built in cm 1:6, complete all as specified and directed. 4 m & l 15 mm thick rendering in cement mortar 1:4 on brick work or concrete surface on wall or ceiling as in fins fascias, chajja louveres, parapets and railing exc 60 cm in height newels , balustrade with chicken wire mesh in two layer of plaster and finished even and smooth without using extra cement, complete all as specified and directed. 5 m&l for preparation of new surface of wall / ceiling and applying three coat of white wash, complete all as specified and directed. 6 s & f joist, channel, angle or tee, square or rectangular, tubler sections, fixed indipendenty or as purlin, rafter, or post including cutting to dead length where required, notching, drilling, fitting, riveting and / or welding or connecting with boldts, complete all as specified and directed. ( fe 410 w ( gde e 250 ) quality a ) , complete all as specified and directed. 7 m & l for preparing new steel surfaces of any description, over 10cm in width or girth, not otherwise describe and evenly applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. 8 s & f pre painted galvalum aluminium zinc coating steel based corrugated steel sheet 0.50mm thick ( total coated thickness ) of any colour having tensile strength of 550 mpa minimum, yeild strength, it shall becoated with hot dip alloy of 55% aluminimum, 43.5% zinc, 1.5% silicon and finished with resin coat on both surface @ 150 gm / sqm of coating as specified and shall be fixed with hot dip galvanised, self drilling and self tapping screws neoprened and edpm washers as in roof covering, complete all as specified and directed. 9 s & f solid pvc wall / ceiling lining consisting of 5mm thick plain colour pvc sheet inclusive of solvent cement and fixing at site on pvc frame including dismantling, complete all as specified and directed. 10 s&f gi frame work for seamless ceiling comprises of gi perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm center to center channel 0.9 mm thick having two unequal flanges of 15 mm each and web of 45 mm suspended from soffit approx 900 mm center to center with gi cleat and steel expansion fastener with and including ceiling section of 0.55 mm thickness having kurled web of 50 mm and flanges of 26 mm each with lips of 10.5 mm fixed to intrermediate channel with connecting clips across the intermediate channel at 457 center to center, complete all as specified and directed. 11 m & l providing precast cement concrete louvers and jallies 50 mm thick of any size as approved by ge including all mouldings , frame etc, complete all as specified and directed. 12 s&f for tmt reinforcement bars 6 8 mm dia including all cutting bending binding cranking placing & binding with ms wire ( annealed ) not less than 0.9 mm dia, complete all as specified and directed. 13 s&f for tmt reinforcement bars 10 mm dia and over including all cutting bending binding cranking placing & binding with ms wire ( annealed ) not less than 0.9 mm dia, complete all as specified and directed. 14 s&f pre painted galvalume aluminium zinc coating steel based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof / covering / cladding to wall, fixed with self tapping screws, complete all as specified and directed. 15 s & f in repair110 mm dia bore. pvc ( swr ) pipes single socketed in any length withrubber ring joints, fixed to walls, complete all as specified and directed. 16 s & f in repair 110 mm dia bore pvc ( swr ) bends any radius with solvent rubber ring joints, fixed, complete all as specified and directed 17 s & f in repair110 mm dia bore pvc ( swr ) junction single, single ( t ) equal or unequal with solvent rubber ring joints, fixed, complete all as specified and directed 18 s&f reienforced cement concretetype b0 1:2:4 beam, cantilever, bressummers, lintels over 1.5 m span, complete all as specified and directed 19 use and waste of formwork to sides and soffits of floor or roof beam , beam haunching , griders bressummers lintels cantilevers sup ports overhanhgs coloumn etc also splays between floor and beam for fair finished surface of concrete, complete all as specified and directed 20 demolition of reinforced cement concrete of any descriptionetc, complete all as specified and directed. 21 demolition of brick work built in cement mortar including all quoins arches pillars etc, complete all as specified and directed. 22 m&l for pcc ( 1:3:6 ) type c 1 with using 20mm graded stone aggregate as in plinth protection, bed blocks, coping, for fixing holdfast / lugs, filling hollow space of pressed steel door frame etc including necessary form work , complete all as specified and directed. 23 desmantling ofplain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof coverings, complete all as specified and directed. 24 excavating over areas, not exceeding 1.50 m deep and getting out in any type of soil complete all as specified and directed. 25 m & l for cement concrete 1:4:8type d 2 ( 40 mm graded aggregate ) as in sub base, foundations, filling and mass concrete, complete all as specified and directed. 26 m & l 25mm thick cement concrete type b 0, 1:2:4 ( 12.5 mm graded aggregate ) as in levelling course in floor complete all as specified and directed. 27 m&l endura 300x300 vitrified full body tiles 12 mm th with water absorption <0.5%, average mor> 38 n / sqmm, breaking strenth >300 n, thermal shock resistance no damage, skid resistance ramp test >r9 alable color, 1st quality / premium in flooring & including 20 mm thick screed bed built in cm 1:4, complete all as specified and directed. 28 m&l granite 20 mm thick ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking plateforms and likeincluding pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite over & incl 20 mm thick screed bed built in cm 1:4, complete all as specified and directed. 29 providing and laying at or near ground level factory made kerb stone of m 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 ( 1 cement: 3 coarse sand ) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm ) , including making drainage opening wherever required, complete all as specified and directed. 30 m&l providing cement concrete 1:2:4 type b 0 ( using 12.5 mm graded crushed stone aggregate as in lintels upto 1.50 metre clear span, cills, steps, seismic & other similar bands, plinth courses, parapets & railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs and the like including weathering, slightly rounded or chamfered angles and throating as directed including necessary form work, complete all as specified and directed. 31 removing excavated material n exc. 50m and depositing where directed at a level n exc 1.5 m above the starting point, complete all as specified and directed. 32 desmantling of framed timber scantlings 40 sq cm and over in section, in any position, complete all as specified and directed. 33 excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for laying of cable etc.n exc 1.5 m in depth and getting out in any type of soil, complete all as specified directed. 34 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm, complete all as specified directed. 35 supplying and laying un reinforced precast concrete cable cover, class lv, type i, flat, size 250 mm x 150mm x 40mm, complete all as specified directed. 36 supply and laying fine sand for cable protection in layers including punning, complete all as specified directed.note: punned thickness shall be measured for the payment. 37 m&l for tubes, medium grade, galvanised, with all fitting of size 50 mm ;laid in trenches for cable protection all as specified and directed 38 supply and laying and testing cable xple insulated, screended , pvc badded galvanised steel strip or wire armoured electric power cable ( heavy duty ) 1100 volts grade with stranded aluminium conductor of25 sqmm4 core, complete all as specified directed. 39 supply and installation and commissioning lt panel board out door type , double door type made out of crca sheet 3 mm thick for outdoor frame and 2 mm thick for innner frame with400 amps rated aluminium bus bar , cubical type duly powder coated with two coat of synthetic enamel paint over a coat of mettalicprimer, incl necessary pcc work for grounting of feeder box 40 cm above the ground level by providing 60 cm long angle iron frame bottom of 40x40x5 mm thick , welded on all four corners , embedded in pcc 1:2:4 type b l complete with comprising the following complete with panel wiring suitable size of copper wire.note: the panel should be cpri approved.incoming: ( a ) mccb tpn 63amps, 415 volts 1 nos, ics=100% icu, ( b ) ammeters 0 100 amps with ct reting and selector switch 01 no ( c ) voltmeter with selector switch 0 500 volts 01 no ( d ) indicatin led lamps ryb ) 0i setoutgoing: ( a ) mcb tpn 63amps, 415 volts 4nos ( b ) mcb spn 32 amps , 415 volts 03 nos 40 m&l hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified directed. 41 m & l 60mm thick machine pressed precast concrete interlocking paver block fixing with grey cement and pigmentsof i shape or as approved by ge, and any colour and size confirming to is 15658 2006 of m 35 grade set, laid over and including 25 mm thick dust sand cushioning, filling of joints with sand & compaction using surface vibrator after filling of joints laid in any pattern as decided by engineer in charge including packing of sides by cement concrete finishing surfce even and smooth, complete all as specified and as directed. 42 earth work in excavation of all kind of soil by mechanical means ( hydraulic excavator ) means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, complete all as specified and as directed. 43 earth work in excavation of all kind of soil by mechanical means ( hydraulic excavator ) / in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) , including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m, complete all as specified and as directed. 44 description same as per item no. 43.00 but each additional 1.5 m or part thereof in depth beyond the first 1.5 m, complete all as specified and as directed. 45 removing excavated material n exc. 50m and depositing where directed at a level n exc 1.5 m above the starting point, complete all as specified and as directed. 46 m&l for rcc ( design mix ) m25 ( 20 mm graded aggregates ) asin foundations, including rafts, footings, foundation beam, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete, complete all as specified and as directed. 47 m&l for rcc ( design mix ) m25 ( 20 mm graded aggregates ) as in columns, pillars, peirs, posts, and struts, complete all as specified and as directed. 48 m&l for rcc ( design mix ) m25 ( 20 mm graded aggregates ) as in beams , cantilivers , bressummers , lintles over 1.5 m span complete all as specified and directed. 49 m&l rcc m 25 ( design mix ) using 20mm graded stone aggregate as in slabs supported on walls, beams, and columns complete all as specified and directed. 50 m&l rcc m 25 ( design mix ) using 20mm graded stone aggregate as chajjas complete all as specified and directed. 51 use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beam, sides and soffits ( if any ) of foundation and plinth beams and similar work, verticalor to batter surfaces for rough finished flat surfaces of concrete, complete all as specified and directed. 52 use and waste of formwork rough finished surface of concrete as in square, rectangular or polygonal to sides of columns, pillars, posts, struts, piers etc.complete all as specified and directed. 53 m&l form work to soffits of suspended slabsuch as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick ( horizointal or slooping ) complete all as specified and directed. 54 m&l formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed. 55 m&l form work to edges of concrate flats, treads, breaks in floors, androof n.exc 20 cm wide and sides of rcc / pcc bands in walls horizontal or sloping and similar work exc 10 cm but not exc 20 cm wide complete all as specified and directed. 56 s&f for tmt reinforcement bars 5 mm dia including all cutting bending binding cranking placing & binding with ms wire ( annealed ) not less than 0.9 mm dia over upto and including 10mm dia in stirrups, spacers and binders etc, complete all as specified and directed. 57 m&l brick work with fly ash modular bricks straight or curved on plan to any radius in half brick thick walls, built in in cement mortar 1:3 complete all as specified and directed. 58 m & l 40 mm thick damp proof course in cement concrete 1:2:4 type b 0 with incorporating integral water proofing compound in the manner specified by the manufacturer and in the proportions indicated, to horizontal or vertical surfaces including necessary formwork complete all as specified and directed. note: wpc will be measured and paid separately. 59 m & l rendering 10 mm thick on brick wall / cement block wall or concrete surfaces in cement mortar 1:6, surfaces finished even and smooth without using extra cement , complete all as specified and as directed. 60 m & l 5 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling surface finish even and smooth without using extra cement , complete all as specified and directed. 61 m & l plastering15 mm thick intwo layers of10 mm thick inbottom and 5 mm thick with wpc oftop layerin cement mortar 1:4 on brick wall / cement block wall or concrete surfaces, surfaces finished even and smooth without using extra cement , complete all as specified and as directed. note: wpc will be measured and paid separately. 62 supply only liquid water proofing compound all as specified and directed. 63 m & l preparation of new wall surface and apply one two of white wash on wall surface includingwashing floors, cleaning glass, joinery, electrical fittings, wiring etc. , of drops and splashes complete all as specified and directed. 64 m&l forapplying 1 mm thick wall care putty on wallon internal old / new wall surfaces as per manufacturerer instruction complete all as specified and as directed 65 m & l for applying two coats of oil bound distemper over a coat of alkali resistant primer on prepared wall putty surfaces of internal wall all includingwashing floors, cleaning glass, joinery, electrical fittings, wiring etc. , of drops and splashes complete all as per specified and directed. 66 m&l preparing of newly plastered or unplastered surfaces of walls, cornices etc and applying two coats of cement base paint over one coat of cement primer, complete all as specified & directed. 67 m&l moorum / red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. 68 m & l 20 25 mm thick machine cut kota stone slab in flooring or treads of steps over and including 20mm thick screed bed in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing complete all as specified and as directed.note: the size of kota stone slab shall not less than 550 mm x 550 mm cut size, except the location where the balance portion remain less than size as specified above. 69 description same as per item no. 68.00 but as in riser of steps, skirting, dado and vertical surfaces including 10 mm thick rendering in cm 1:4, complete all as specified and directed. 70 s & f framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to fe.290.gde e 165, complete all as specified and directed. 71 s & f powder coated aluminium sliding glazedwindows with three track shutter sliding ( two shutters glazed and one shutterwire mesh ) shall be following specification, complete all as specified and directed. ( i ) windows frame of cross section 101mm x 44mm x 1.5mm thick. ( ii ) three way track for sliding shutters of cross section91.8mm x 31.75mm x1.1mm thick. ( iii ) sliding shutter frame of cross section40 x 18 x 1mm thick. ( iv ) 4 mm thick tintedglass superior quality. ( v ) idpe rubber guasket for fixing of glass. ( vi ) locking cleats per shutter 01 nos. ( vii ) sliding rollers per shutter 02 nos. ( viii ) aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56mm for shutters 01 nos. 72 s&f powder coated aluminium ventilator cross section 63.5x38.10x1.5mm consisting of two partions upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with idpe rubber gasket including aluminium beads, including preparation of jombs all around in cm 1:3 finishing even and smooth complete all as specified and directed. 73 cutting holes in brick walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type b 1, complete all as specified and directed. 74 s&f pressed steel frames size 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed. 75 s&f2nd class hard wood 35 mm thick plain, framed, pannelled shutters ( any number of panels ) , with panels of timber flat on both sides ( feather edged ) , or of veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed. 76 s&f2nd class hard wood 35 mm thick glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc, ( without sash bars ) , edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securingglass, etc, size of members of shutters as specified in ssr part i, section 8, clause8.24 ( a ) complete all as specified and directed.note : glass pane and wire mesh shall be measured and paid separately inrespective supply only item. 77 supply only galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed. 78 m & l preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise description, over 10 cm width or girth apply two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 79 s&f factory made solid pvc door frame of size 50 mm x 47 mm made out of 5 mm plain colour pvc sheet reinforced with ms square tube, all as specified and directed. 80 s&f 30 mm thick factory made solid panel pvc door shutter ( style ) consisting of frame made out of m.s. tubes of 19 gauge thick & size 19mmx19mm for stiles and 15mmx15mmfor top & bottom rails. m.s. frame shall have a coat of red oxide primer of approval make and shall becovered with 5 mm thick heat moulded plain colour pvc ‘c’ channel of size 30x50mm forming stiles and 5 mm thick wide pvc sheets for top rail , lock rail and bottom rail on either side and 10 mm ( 5mmx2mm ) thick having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour 5mm thick pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with 30 mm widex5 mm thick pvc , sheet suitable pvc sheet beading, and joined together with solvent cement on either side, and additional 5 mm thick pvc stripes of 20 mm width is to be struck on interior side of c channel using pvc solvent adhesive complete at site as per specification complete all as specified and as directed. 81 s&f aluminium anodised barrel tower bolts 150 mm long of extruded section and fixed complete all specified and directed. 82 s&f aluminium anodised barrel tower bolts 200 mm long of extruded section and fixed complete all specified and directed. 83 s&f aluminium handles, size 150 mm cast type, anodised complete all as specified and directed. 84 s & fbutt hinges, size 100 mmtype c 21 extruded aluminium alloy with galvanised mild steel hinge pin, anodised isi marked, complete all as specified and directed. 85 s&f 250 mm long aluminium alloy, anodised sliding door bolt with hasp, staple ( bolt type ) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy fixed, complete all as specified and directed. 86 s & f vitreous china squatting pan orissa patern size 580 mm x 440 mm, white, with integral foot rest ( excluding flushing cistern and flush pipe ) including connection to trap and to flushing pipe, anti syphonage pipe, etc complete all as specified and dircted. 87 s & f 10 litres capacity pvc low level cistern ‘ white’ with inlet, float valve and handle including flushing pipe of pvc 32 mm dia and connection to pipes complete all as specified and directed. 88 s & f chromium plated fancy type stop cock / angle cock 15 mm dia cast copper alloy screwed down, high pressure, with crutch or butter fly handle screwed both ends for iron pipeor for unions and fixed, complete all as specified & directed. 89 s & f pvc connection 15 mm dia 600 mm long with ptmt nuts at both ends complete all as specified and directed. 90 s & f 15 mm bore bib taps chromium plated fancy type cast copper alloy crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, and fixed complete all as specified and directed. 91 s & f vitreous china wash hand basin white or any colour , flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia pvc waste pipe complete all as specified and directed. 92 supply only 15 mm dia bore fancy type chromium plated pillar tap, cast copper alloy, with capstan heads, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe and fixed, complete all as specified and directed. 93 s&f 600mmx450mm bevelled edge looking mirror of selected quality glass, mounted on 6 mm thick ac building board or commercial plywood and fixed to wooden / pvc plugs with chromium plated brass screws and cup washer 94 s & f brass chromium plated tubular towel rail, 20mm dia d type 60 cm long between flanges complete all as specified. 95 s & f vitreous china bowl urinal flat back, size, of 465 x 355 x 265 mm white ( minimum ) , with grating and union for discharge pipe complete all as specified and directed. 96 s&f pvc ( swr ) 75 mm bore pipes single socketed in any length with rubber ring joints with solvent cement fixed to walls&flooor incluidng clamping complete all as specified and directed. 97 s & f in 75 mm bore pvc ( swr ) bends any radius with solvent rubber ring joints, fixed, complete all as specified and directed. 98 s & f in 75 mm bore pvc ( swr ) junction single, single ( t ) equal or unequal with solvent rubber ring joints, fixed, complete all as specified and directed 99 s & f pvc ( swr ) nahani trap / floor trap with grating having diameter of outlet 75 mm including jointing to waste pipe with solvent cement complete. 100 s & f110 mm bore pvc ( swr ) vent cowl including taking out existing unserviceable cowl, complete all as specified and directed. 101 s & f of cpvc 20 mm outer dia pipessdr 11 & plain cpvc sdr 11 fittings on walls / ceiling or laying in floors, complete all as specified and directed. 102 s & f of cpvc 25 mm outer dia pipessdr 11 & plain cpvc sdr 11 fittings on walls / ceiling or laying in floors, complete all as specified and directed. 103 s & f of cpvc brass elbow ( 3 / 4 x ½ ) for 20 mm outer dia cpvc pipe complete all as specified and directed. 104 s & f of cpvc male brass threaded adaptor ( mta / mbta ) for 25 mm outer dia pipe complete all as specified and directed. 105 s & f of cpvc ball valve for 25 mm outer dia pipe complete all as specified and directed. 106 s&f rotational moulded poly ethylene water storage tanks ( isi marked ) ( cylinderical vertical with closed top ) 1000 litres capacity , hoisted and fixed in position including dismantling of pvc water tanks exc 500 ltr but not exc 1000 ltr, complete all as specified and directed. 107 s&f ball valves high pressure of ptmt with epoxy coated aluminium rod & high density plastic ball , suitable for 25 mm bore pipe, screwed for iron pipe and fixed. . ( minimum weight 25mm 455 gms. ) complete all as specified and directed. 108 m & l non skid ceramic coloured tiles 7 to 8 mm thick ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exc 0.18 sqm , in floors etc.set jointed in neat cement sluury and pointed in white or coloured cement to match over & incl 15 mm thick screed bed built in cm 1:6, complete all as specified and directed 109 m&lglazed ceramic coloured tiles on vertical surfaces 450x350x7 mm / 450x300x7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick backing coat to receiving to wall tiles incement mortar 1:4, complete all as specified and directed. 110 m&l granite 20 mm thick ( of any type ) work ( table rubbed and polished ) in steps, jambs, pillars, window cills, cooking plateforms and likeincluding pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with shade of granite over & incl 20 mm thick screed bed built in cm 1:4, complete all as specified and directed. 111 m&l rounding to edges of stone slabs one edges, such as in steps, cooking platform, and other similar situations for bullnosing / moulding to exposed edges ( any type ) and polishing to match the adjoining surfaces, complete all as specified and directed. 112 s & f tubular rolled sections as post, rafter, purlin, and its connected wk for shed structure and similar work complete using erw or induction butt welded tubes conforming to i.s. 1161 1976 grade st. 240, complete all as specified and directed. 113 s & f pre painted galvalume aluminium zinc coating gi based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in sun shade, roof covering / cladding to wall, and similar work fixed with self tapping screws complete all as specified and directed. 114 m&l water proofing treatment on non approachable / non accessible roof surface ( horizontal & vertical surfaces ) in following sequence through authorized applicator of the manufacturer all as specified and directed complete. ( i ) cleaning of new rendered surfaces properly and drying the surfaces. ( ii ) applying a coat of oxidised bitumen based solvent primer @ 0.30 kg / sqm ( iii ) laying 3 mm thick app modified water proofing membrane with 100 mm over laps sealed and bounded to the surfaces by torchon method. ( iv ) applying two coats of bitiminous aluminium paint @ 200 gram / sq m ( minimum ) in two coats .make incorporated : hyperplas polyster of iwl ( india ) ltd or equivalent in pidilite industrries ltd / stp ltd all as specified and as manufacturer instruction , complete all as specified and directed. 115 m&l salt glazed stoneware drain pipes 150 mm internal dia ofgrade ‘a’ laid in trenches & jointed as specified, complete all as specified and directed. 116 m & l 1:3:6 typec 2 using 40 mm graded stone aggregate cement concrete bedto drain pipe including packing under and haunching against side of pipe for150 mm bore ofpipe complete all as specified and directed 117 s&f sand stone slab in sun shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n.exc. 2m in length, punched dressed on faces and along exposed edges, self faced on other side, thickness of sand stone slabs 50 mm thick, complete all as specified and directed. 118 s & f reinforced concrete pipes 300 mm bore, class np2 , laid and jointed complete with collars, including demolition and breaking up drain pipes, complete all as specified and directed. 119 m&l point wiring with 1.5 sqmm ( nominal cross sectional area ) single core, pvc insulated, unsheathed frlsh copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non metallic, rigid non mettalic pvc conduit ( medium grade ) concealed in wall / ceilingwith and including 1.5 sqmm single core pvc insulated, multistranded, unsheathed, frlsh copper conductor cable as continuous earth continuity conductor ( green in colour ) with cast iron / pressed steel modular terminal boxes any size / module, conceiled on walls and fixed by neans of brass screws incl modular cover plates and cover frme any size / module, for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessoriesone light / fan / bell controlled by one, one way switch 5 / 6 amps, complete all as specified and directed. 120 description same as per item no. 119.00 but for one 3 pin, 5 / 6 amps socket outlet point on independent boardcontrolled by one, one way 5 / 6 amps switch, complete all as specified and directed. 121 description same as per item no. 119.00 but for one 3 pin, 5 / 6 amps socket outlet point on same boardcontrolled by one, one way 5 / 6 amps switch, complete all as specified and directed. 122 m&l point wiring with 2.5 sqmm ( nominal cross sectional area ) single core, pvc insulated, unsheathed frlsh copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non metallic, rigid non mettalic pvc conduit ( medium grade ) concealed in wall / ceilingwith and including 2.5 sqmm single core pvc insulated, multistranded, unsheathed, frlsh copper conductor cable as continuous earth continuity conductor ( green in colour ) with cast iron / pressed steel modular terminal boxes any size / module, conceiled on walls and fixed by neans of brass screws incl modular cover plates and cover frme any size / module, for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one 15a socket point independentcompleteall as specified and directed. 123 s&fceiling rosethree terminals surface bakelite type, ac, 50 hz, 230v complete all as specified and directed. 124 s&f modular switch1 way 6 a , 1 modulecomplete all as specified and directed. 125 s&fmodular socket 6 amps 2 / 3 pin combined2 module complete all as specified and directed. 126 s&f switch modular type 16 a, 1 module complete all as specified and directed. 127 s&fsocketmodular type multipurposes 6 / 16 a, 2 module complete all as specified and directed. 128 supply and fixing surface / wall mounted led batten poly carbonate housingfor retrofitled tube t 8 type upto 1x20 watt, 4 feet longpre wired incl integrated electronic driver complete with all connectedaccessories all as specified and directed. 129 supply and fixing retrofitled tube t 8 type1x20 watt, 5700 to 6500 k and thd less than 15% , polycarbonate body , glass tube 4 feet longcomplete with 02 years warrenty all as specified and directed. 130 s&f 10 w led batten 2 feet long, wall mounted, extruded aluminium heat sink provided for efficient heat dissipation & integrated electronic driver with system efficiency 110 lumen / watt, lumen output >=1100 lumen complete all as specified and directed. 131 supply and fixingexhaust fans ac single phase 230 voltpvc bodyof size 250mm sweep with louver completeincluding provision of pvc flexible copper cable of size 23 / 0.0076 two core from ceiling rose to exhaust fan forconnection andcutting opening of windowsfor fanbase ( ply wood sheet 12 mm thickrequired size ) , necessary fixing arrangements complete all as specifiedand directed.note : cost of suitable opening window and 12 mm thick ply woodfor fixing exhaust fan is deemed to be includedin overall rate quoted. 132 s & fled bldg security light fitting30wattmade up of pressure die cast aluminium housing with highly efficient leds as lighting source with acylic cover as diffuser with ip 66 and ik 07 protection thd < 10% lumen output >=110 lumen per watts complete incl gi pipe 40 mm size 1 meter bend into size for fixing of security light with suitable bracket complete all as specified and directed. 133 s&f mcb db spn 12 way double doorip 43, ik 09 with 200 amps rated bus bar , 230 volts, 50 hz complete all as specifed and directed. 134 supply & fixmcb spn 32 amps current rating c series 10 ka breaking capacity of the same make as item no 13 complete all as specified and directed. 135 supply & fixmcb sp 6 to 32 amps current rating c series 10 ka breaking capacityof the same make as item no 13 complete all as specified and directed. 136 supply and fixing tv socket outlet complete all as specified and as directed. 137 supply and fixing telephonejacket complete all as specified and as directed. 138 m & l sub main wiring with 2 runs of 4 sqmm main wire along with 1 run of 4 sqmm earth wire ( green in colour ) single core frlsh pvc insulated, unsheathed, multi stranded, 1100 volts grade isi marked copper conductor cable, drawn through and including adequate size rigid non metallic pvc concealed / surface conduit ( medium grade ) wherever necessary with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good disturbed surfaces complete all as specified and directed.note: two runs of main copper conductor, one run of earth wire and one run of pvc conduit shall be measured as one unit length. 139 s&f exhaust fan , steel body ac single phase230 volt of size 300 mm mmsweep complete with blade, frame and louvers all as specified and directed incl making of hole in brick work wherever necessary making good disturbed surface, painting to match with existing surfaces, complete all as specified and as directed. 140 supply , fixingrigid non metallic pvc conduit fixed conceiled / on wall wherever necessary with all connectedaccessories20 mm dia forcable tv connections, complete all as specified and as directed. 141 supply and fixin replacement of ceiling fan 1200 mm sweep , bldc fan with power factor of > / =.0.90 for air delivery of 220 m / cum minimum service value of 8 with capacitor type modularfan regulator ( without remote ) , completeall as specifeid and as directed. 142 supplying, laying, fixing, jointing and testing lt under groundxlpe insulated, galvanised steel strip or wire armoured heavy duty electric cable with aluminium conductor , multi stranded 1100 volts grade, cross sectional area 16 sq. mm 2core, isi 7098 marked, with electric connection lugs, laid in trenches / under floor under pcc / interlocking tiles incl making good of surface with pcc / cementing or fixed naked with walls / on poles / in ducts / in gi pipes etc and including taking down completetrenches / all as as directed at site.note: excavation, earth work, sand cushioning, protection tiles / brick / block shall be measured and paid seperately. 143 tubes, light grade, galvanised, with all fitting of size 40 mm ;laid in trenches for cable protection all as specified and directed. 144 m&lof earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick, buried directly in ground vertically to a depth not less than 2.25 meters deep below ground levelwith top edge of the plate not less than 1.5 mtrs below normal ground level connect to galvanised earth lead wire of 4.0 sqmm size by means of bolts, nuts, check nuts and washers of galvanized iron or steel up to 7.5 meter length including connected to earth plate including necessary excavation & earthwork, pcc ( 1:3:6 ) type c 1 earth chamber, 40 mm thick rcc cover 1:2:4 mix with 6mm dia nominal reinforcement @ 150 mm c / c both ways etc completeall as shown in electrical plate no 5, connected to earthing test point complete including testing on completion all as specified....

Military Engineer Services - Madhya Pradesh

34782467 special repair / replacement of certain ber equipments in tech area at af stn gwalior supply, install, commissioning and testing of split type wall mounted air conditioner of capacity 1.5 tr ( 4500 k cal / hr ) single phase, ( non cfc / hchc ) suitable for 230 volt + 10% , 50 hz, ac supply complete with cordless remote control unit , minimum 3 star rating eer of 3.2 and above complete comprising of following : make : blue star, model no vltu fixed speed ac3 star or equivalent in make :voltas / carrier / daikin / hitachi. ( a ) indoor unit copper coil with three speed blower fan of appropriate capacity including pcb, thermostatic control, air filter and drain for condensing water. ( b ) out door unit comprising . compressorwithmotor, . air cooled copper condenser with fan and motor .unitshall be installedout side the building / on roof. ( c ) refrigerant copper pipe for suction and discharge line with insulation , condensing water drain pipe& protected by suitable size of flexible pvc conduit with control valves & safety accessories including control wiring for evaporator & condensing unit with suitable size of copper cable. ( d ) making good the disturbed surface to match the existing surface after plugging the hole etc. ( e ) pcc ( 1:2:4 ) type b 1 ( using 20 mm graded stone aggregate ) as in plinth suitable for installation of outdoor unit or powder coated ms bracket fixed on wallas per manufactures instruction with necessary grouting ms hold fast, bolts, washers duly painted and making good to disturbed surfaces suitable for installing outdoor unit of 1.5 tr ac complete all as specified and directed. ( f ) electrical cable required to connect out door unit and indoor unit to voltage stablizer inclusive in above rate. 2 supply, install, commissioning and testing of split type wall mounted air conditioner of capacity 2 tr ( 6000 k cal / hr ) single phase, ( non cfc / hchc ) suitable for 230 volt + 10% , 50 hz, ac supply complete with cordless remote control unit , minimum 3 star rating eer of 3.2 and above complete comprising of following : make : blue star, model no aatx fixed speed ac3 star or equivalent in make :voltas / carrier / daikin / hitachi. ( a ) indoor unit copper coil with three speed blower fan of appropriate capacity including pcb, thermostatic control, air filter and drain for condensing water. ( b ) out door unit comprising . compressorwithmotor, . air cooled copper condenser with fan and motor .unitshall be installedout side the building / on roof. ( c ) refrigerant copper pipe for suction and discharge line with insulation , condensing water drain pipe& protected by suitable size of flexible pvc conduit with control valves & safety accessories including control wiring for evaporator & condensing unit with suitable size of copper cable. ( d ) making good the disturbed surface to match the existing surface after plugging the hole etc. ( e ) pcc ( 1:2:4 ) type b 1 ( using 20 mm graded stone aggregate ) as in plinth suitable for installation of outdoor unit or powder coated ms bracket fixed on wallas per manufactures instruction with necessary grouting ms hold fast, bolts, washers duly painted and making good to disturbed surfaces suitable for installing outdoor unit of 2 tr ac complete all as specified and directed. ( f ) electrical cable required to connect out door unit and indoor unit to voltage stablizer inclusive in above rate. 3 supply, install, commissioning and testing of split type air conditioner of capacity 3 tr ( 9000 k cal / hr ) three phase, ( non cfc / hchc ) suitable for 230 volt + 10% , 50 hz, ac supply complete with cordless remote control unit , minimum 3 star rating eer of 3.2 and above complete comprising of following : make : blue star, model no fma36aamup3 or equivalent in make :voltas / carrier / daikin / hitachi. ( a ) indoor unit copper coil with three speed blower fan of appropriate capacity including pcb, thermostatic control, air filter and drain for condensing water. ( b ) out door unit comprising . compressorwithmotor, . air cooled copper condenser with fan and motor .unitshall be installedout side the building / on roof. ( c ) refrigerant copper pipe for suction and discharge line with insulation , condensing water drain pipe& protected by suitable size of flexible pvc conduit with control valves & safety accessories including control wiring for evaporator & condensing unit with suitable size of copper cable. ( d ) making good the disturbed surface to match the existing surface after plugging the hole etc. ( e ) pcc ( 1:2:4 ) type b 1 ( using 20 mm graded stone aggregate ) as in plinth suitable for installation of outdoor unit or powder coated ms bracket fixed on wallas per manufactures instruction with necessary grouting ms hold fast, bolts, washers duly painted and making good to disturbed surfaces suitable for installing outdoor unit of3 tr ac complete all as specified and directed. ( f ) electrical cable required to connect out door unit and indoor unit to voltage stablizer inclusive in above rate. 4 m & l for sub main wiring with two runs of single core 4 sq.mm for phase conductor and one run of single core 4 sq.mm as earth wire ofmulti stranded copper conductor fr lsh pvc insulated unsheathed cable conforming to is : 694 drawn through in & including pvc casing & capping with fixing accessories on wall / roof surface as per relevent is standard not less than 25 mm width and all as complete including taking down existing unserviceable specified and directed. 5 m & l for sub main wiring with three runs of single core 4 sq.mm for phase conductor and one run of single core 4 sq.mm as earth continuity conductor ofmulti stranded copper conductor fr lsh pvc insulated unsheathed cable conforming to is : 694 drawn through in & including pvc casing & capping with fixing accessories on wall / roof surface as per relevent is standard not less than 30 mm width and all as complete including taking down existing unserviceable specified and directed. 6 supply and fixing industrial type socket with plug top, single pole and netural and earth plug 240v, 20 amps with steel enclosure and one mcb spn20 amps complete including taking down existing unserviceable specified and directed. 7 supply and fixing industrial type socket with plug top, tripple pole and netural and earth plug 415v, 32 amps with steel enclosure and one mcb tpn 32 amps complete all as specified and directed. 8 supply and fixing voltage stablizer electronic typefor automatic operation single phase naturally air cooled, indoor type, wall mounted for input variation between 170 v to 280 v with output voltage stablized at 200v to 245 v with accuracy of + 1% and of capacity 5.0 kva complete including taking down existing unserviceable specified and directed make: v guard, model no vnd 500 or equivallent make : blue bird, ae, v guard 9 supply and fixing copper tubing of special annealed pressure copper of size 3 / 8 bore 10 supply and fixing copper tubing of special annealed pressure copper of size 5 / 8 bore 11 supply and fixing copper tubing of special annealed pressure copperof size 1 / 4 bore 12 supply and fixing copper tubing of special annealed pressure copper of size 1 / 2 bore 13 supply and fixing pvc nylon braided industrial quality drain pipe of 20mm inner bore including fixing accessories on wall / roof etc all as directed...

Northern Coalfields Limited - Madhya Pradesh

34507565 bids are invited for the detailed technical specification is mentioned in boq item sl no 1 of attached nit at annexure xiv excavation of pole pit , the detailed technical specification is mentioned in boq item sl no 2of attached nit at annexure xiv excavation of stay pit , the detailed technical specification is mentioned in boq item sl no 3of attached nit at annexure xiv fixing of disc insulator , the detailed technical specification is mentioned in boq item sl no 4of attached nit at annexure xiv fixing of post insulator , the detailed technical specification is mentioned in boq item sl no 5of attached nit at annexure xiv laying of dog conductor , the detailed technical specification is mentioned in boq item sl no 6of attached nit at annexure xiv laying of earth wire , the detailed technical specification is mentioned in boq item sl no 7of attached nit at annexure xiv fabrication of ms channel , the detailed technical specification is mentioned in boq item sl no 8of attached nit at annexure xiv dismantling of rail pole , the detailed technical specification is mentioned in boq item sl no 9of attached nit at annexure xiv dismantling overhead line materials , the detailed technical specification is mentioned in boq item sl no 10of attached nit at annexure xiv supply of gi earth wire , the detailed technical specification is mentioned in boq item sl no 11of attached nit at annexure xiv supply of bolts ms black hex head , the detailed technical specification is mentioned in boq item sl no 12of attached nit at annexure xiv supply of hard ware for wolf conductor , the detailed technical specification is mentioned in boq item sl no 13of attached nit at annexure xiv supply of stay assembly , the detailed technical specification is mentioned in boq item sl no 14of attached nit at annexure xiv painting with aluminium paint total quantity : 40462...

West Central Railway - Madhya Pradesh

34300372 supply of supply of surge protection device .supply of surge protection device ., supply of surge protection device for telecom network protection, mdf base technology with screw less type connectors of modular wago connector suitable wall or panel mounting provision , stainless steel box, system nominal voltage 5 volt, max. response time should be less than 1 ns , must be available earth wire on the outside body of the spd, make / model jmv d30 or similar ....

Northern Coalfields Limited - Madhya Pradesh

33428143 bids are invited for shifting of west sub station of jayant project 33kv 1250a isolator pole off load isolator horizontal cut with earthing switch 6600 v 1250 a triple pole off load isolator horizontal type complete set 33kv station type current transformer . the detailed technical specifications mentioned in boq sl no 3 of annexure xiv 33kv 110v pt burden 100va 01 set of 03 nos overhauling of 33kv 1250a sf6 circuit breaker with control relay panel providing lightning arrestor 30kv 10ka station type 01 set of 03 nos overhauling 6600 v 1250amp vcb outdoor type with control relay panel the detailed technical specifications mentioned in boq sl no 7 of annexure xiv overhauling 6600 v 1250amp vcb outdoor type with control relay panel the detailed technical specifications mentioned in boq sl no 8 of annexure xiv 110v battery battery dc ni cd acid maintenance free battery 200ah 55 nos cells each cell 02 volt 110 volt battery charger 3phase 415 v input and 110v dc output with float and boost charging 25amp to 35amp lighting distribution board consist of incomer mccb 250a and different rating for controlling different lighting circuits along with spares as per requirement lightening arrestor 7kv 5va station type 01 set of 03 nos 1100 v grade copper control cable the detailed technical specifications mentioned in boq sl no 13 of annexure xiv dc power distribution board consist of incomer and sufficient number of outgoing feeder the detailed technical specifications mentioned in boq sl no 14 of annexure xiv supply of bus bar the detailed technical specifications mentioned in boq sl no 15 of annexure xiv designing laying erection testing and commissioning of earthing arrangement the detailed technical specifications mentioned in boq sl no 16 of annexure xiv structural steel work with new mild steel supply fabrication erection and painting work in the scope of bidder as per boq sl no 17 of nit annexure xiv supply of misc items nut bolt clamps pad gi strip ect erection of 13 or 16 mtr pole for lighting arrangement erection and commissioning for item sl no 1 3 4 5 6 7 8 9 10 11 12 13 14 and 15 fabrication erection and painting of steel structure and commissioning dismantling shifting erection and commissioning of bus bar with structure insulators etc as per requirement dismantling shifting erection and commissioning of 33kv 1250a isolator with or without earth switch as per requirement dismantling shifting erection and commissioning of 33kv 10ka lightning arrestor as per requirement dismantling shifting erection and commissioning of 33kv grade current transformer the detailed technical specifications mentioned in boq sl no 25 of annexure xiv dismantling shifting erection and commissioning of 33kv pt as per requirement dismantling shifting erection and commissioning of 33kv 1250a sf6 circuit breaker with control panel and tap changer as per requirement dismantling shifting erection and commissioning of 33kv 1250a circuit breaker with control panel as per requirement dismantling shifting erection and commissioning of 10mva 33kv 6600 v transformer as per requirement dismantling shifting erection and commissioning of 6600 v isolator 1250 or 800 a as per requirement dismantling shifting erection and commissioning of 6600 v 1250a circuit breaker with control relay panel as per requirement dismantling shifting erection and commissioning of 6600 v 1250a or 630a circuit breaker with control relay panel as per requirement dismantling shifting erection and commissioning of ngrs as per requirement erection of armoured copper control cable. the detailed technical specifications mentioned in boq sl no 34 of annexure xiv earth work in excavation by mechanical means hydraulic excavator or manual means in foundation trenches or drains the detailed technical specifications mentioned in boq sl no 35 of annexure xiv excavation work by mechanical means hydraulic excavator or manual means in foundation trenches or drains the detailed technical specifications mentioned in boq sl no 36 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering the detailed technical specifications mentioned in boq sl no 37 of annexure xiv brick work with non modular fly ash lime bricks the detailed technical specifications mentioned in boq sl no 38 of annexure xiv brickwork with non modular falg bricks the detailed technical specifications mentioned in boq sl no 39 of annexure xiv providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering shuttering finishing and reinforcement the detailed technical specifications mentioned in boq sl no 40 of annexure xiv reinforced cement concrete work in walls any thickness including attached pilasters etc the detailed technical specifications mentioned in boq sl no 41 of annexure xiv reinforced cement concrete work in beams suspended floors roofs having slope the detailed technical specifications mentioned in boq sl no 42 of annexure xiv providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering the detailed technical specifications mentioned in boq sl no 43 of annexure xiv centering and shuttering including strutting, propping etc and removal of form for the detailed technical specifications mentioned in boq sl no 44 of annexure xiv centering and shuttering including strutting propping etc and removal of form for columns pillars piers abutments posts and struts centering and shuttering including strutting propping etc and removal of form for lintels beams plinth beams girders bressumers and cantilevers the detailed technical specifications mentioned in boq sl no 46 of annexure xiv centering and shuttering including strutting propping etc and removal of form for suspended floors roofs landings balconies and access platform centering and shuttering including strutting propping etc and removal of form for weather shade chajjas corbels etc including edges centering and shuttering including strutting propping etc and removal of form for walls any thickness including attached pilasters butteresses plinth and string courses etc providing and fixing 1 mm thick ms sheet door with frame the detailed technical specifications mentioned in boq sl no 50 of annexure xiv supplying and fixing rolling shutters of approved make made of required size the detailed technical specifications mentioned in boq sl no 51 of annexure xiv providing and fixing ms grills of required pattern in frames of windows etc the detailed technical specifications mentioned in boq sl no 52 of annexure xiv structural steel work in single section fixed with or without connecting plate including cutting hoisting fixing in position and applying a priming coat of approved steel primer all complete cement concrete flooring the detailed technical specifications mentioned in boq sl no 54 of annexure xiv providing and laying vitrified tiles in different sizes the detailed technical specifications mentioned in boq sl no 55 of annexure xiv providing and laying vitrified floor tiles in different sizes thickness to be specified by the manufacturer with water absorption the detailed technical specifications mentioned in boq sl no 56 of annexure xiv providing and fixing 10 mm thick acid and or alkali resistant tiles of approved make and colour using acid and or alkali resisting mortar bedding, and joints filled with acid and or alkali resisting cement as per is the detailed technical specifications mentioned in boq sl no 57 of annexure xiv providing and fixing 10 mm thick acid and or alkali resistant tiles of approved make and colour using acid the detailed technical specifications mentioned in boq sl no 58 of annexure xiv 12 mm cement plaster of mix the detailed technical specifications mentioned in boq sl no 59 of annexure xiv 6 mm cement plaster of mix the detailed technical specifications mentioned in boq sl no 60 of annexure xiv providing and fixing ms fan clamp type i or ii of 16 mm dia ms bar bent to shape with hooked ends in rcc slabs the detailed technical specifications mentioned in boq sl no 61 of annexure xiv providing and fixing on wall face unplasticised rigid pvc rain water pipes the detailed technical specifications mentioned in boq sl no 62 of annexure xiv providing and fixing on wall face unplasticised pvc moulded fittings or accessories for unplasticised rigid pvc rain water pipes the detailed technical specifications mentioned in boq sl no 63 of annexure xiv providing and fixing on wall face unplasticised pvc moulded fittings accessories for unplasticised rigid pvc rain water pipes the detailed technical specifications mentioned in boq sl no 64 of annexure xiv providing and placing on terrace at all floor levels polyethylene water storage tank the detailed technical specifications mentioned in boq sl no 65 of annexure xiv finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade the detailed technical specifications mentioned in boq sl no 66 of annexure xiv distempering with oil bound washable distemper of approved brand and manufacture to give an even shade the detailed technical specifications mentioned in boq sl no 67 of annexure xiv providing and fixing water closet squatting pan indian type wc pan with 100 mm sand cast iron p or s trap 10 litre low level white pvc flushing cistern including flush pipe the detailed technical specifications mentioned in boq sl no 68 of annexure xiv providing and fixing wash basin with ci brackets 15 mm ptmt pillar cock 32 mm ptmt waste coupling of standard pattern including painting of fittings and brackets the detailed technical specifications mentioned in boq sl no 69 of annexure xiv providing and fixing gi pipes complete with gi fittings and clamps the detailed technical specifications mentioned in boq sl no 70 of annexure xiv providing and fixing gi pipes complete with gi fittings and clamps the detailed technical specifications mentioned in boq sl no 71 of annexure xiv providing and fixing ptmt bib cock of approved quality and colour the detailed technical specifications mentioned in boq sl no 72 of annexure xiv steel reinforcement for rcc work including straightening cutting bending placing in position and binding all complete above plinth level the detailed technical specifications mentioned in boq sl no 73 of annexure xiv providing hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses bands copings the detailed technical specifications mentioned in boq sl no 74 of annexure xiv making soak pit the detailed technical specifications mentioned in boq sl no 75 of annexure xiv providing and fixing isi marked oxidised ms sliding door bolts with nuts and screws etc complete the detailed technical specifications mentioned in boq sl no 76 of annexure xiv providing and fixing isi marked oxidised ms tower bolt black finish barrel type with necessary screws the detailed technical specifications mentioned in boq sl no 77 of annexure xiv filling available excavated earth excluding rock in trenches plinth sides of foundations etc in layers not exceeding 20cm in depth the detailed technical specifications mentioned in boq sl no 78 of annexure xiv 12 mm cement plaster finished with a floating coat the detailed technical specifications mentioned in boq sl no 79 of annexure xiv painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work the detailed technical specifications mentioned in boq sl no 80 of annexure xiv providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length the detailed technical specifications mentioned in boq sl no 81 of annexure xiv finishing walls with water proofing cement paint of required shade the detailed technical specifications mentioned in boq sl no 82 of annexure xiv supplying and filling in plinth with sand under floors including watering ramming consolidating and dressing complete supplying and stacking at site stone aggregate 40 mm noimnal size spreading and levelling to gradient kankar or shingle or gravel or moorum or red bajri etc providing and fixing ptmt stop cock of approved quality and colour the detailed technical specifications mentioned in boq sl no 86 of annexure xiv earthwork in excavation in overburden all operation mechanically with all lifts complete as per instruction of eic the detailed technical specifications mentioned in boq sl no 87 of annexure xiv providing and fixing soil, waste and vent pipes 100 mm dia sand cast iron sands pipe as per is 1729 providing and filling the joints with spun yarn cement slurry and cement mortar the detailed technical specifications mentioned in boq sl no 89 of annexure xiv providing and fixing ms holder bat clamps of approved design to sand cast iron or cast iron spun pipe embedded in and including cement concrete blocks the detailed technical specifications mentioned in boq sl no 90 of annexure xiv providing and fixing bend of required degree with access door insertion rubber washer 3 mm thick bolts and nuts complete the detailed technical specifications mentioned in boq sl no 91 of annexure xiv providing and fixing ptmt towel rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fittings arrangement of approved quality and colour 450 mm long towel rail with total length of 495 mm 78 mm wide and effective height of 88 mm weighing not less than 170 gms the detailed technical specifications mentioned in boq sl no 92 of annexure xiv providing and laying cement concrete the detailed technical specifications mentioned in boq sl no 93 of annexure xiv providing and fixing beveled edge mirror of superior glass of approved quality complete with 6 mm thick hard board ground fixed to wooden cleats with cp brass screws and washers complete the detailed technical specifications mentioned in boq sl no 94 of annexure xiv providing corrugated gs sheet roofing including vertical or curved surface fixed with polymer coated j or l hooks the detailed technical specifications mentioned in boq sl no 95 of annexure xiv providing ridges or hips of width 60 cm overall width plain gs sheet fixed with polymer coated j or l hooks the detailed technical specifications mentioned in boq sl no 96 of annexure xiv providing and fixing tiled false ceiling of specified materials the detailed technical specifications mentioned in boq sl no 97 of annexure xiv extra for providing and fixing wind ties the detailed technical specifications mentioned in boq sl no 98 of annexure xiv providing and fixing mild steel round holding down bolts with nuts and washer plates complete the detailed technical specifications mentioned in boq sl no 99 of annexure xiv wiring for light or power plug the detailed technical specifications mentioned in boq sl no 100 of annexure xiv wiring for light point or fan point or exhaust fan point or call bell point the detailed technical specifications mentioned in boq sl no 101 of annexure xiv wiring for circuit or submain wiring alongwith earth wire with the following sizes of frls pvc insulated copper conductor the detailed technical specifications mentioned in boq sl no 102 of annexure xiv supplying and fixing of following sizes of medium class pvc conduit along with accessories in surface or recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm the detailed technical specifications mentioned in boq sl no 103 of annexure xiv supplying and fixing following piano type switch or socket on the existing switch box or cover including connections etc as required 5 or 6 amps switch supplying and fixing following piano type switch or socket on the existing switch box or cover including connections etc as required 15 or 16 a switch supplying and fixing following piano type switch or socket on the existing switch box or cover including connections etc as required 3 pin 5 or 6 a socket outlet supplying and fixing following piano type switch or socket on the existing switch box or cover including connections etc as required 6 pin 15 or 16 a socket outlet supplying installing testing and commissioning of following capacity tpn tap off box the detailed technical specifications mentioned in boq sl no 108 of annexure xiv earthing with gi earth pipe the detailed technical specifications mentioned in boq sl no 109 of annexure xiv supplying and laying gi strip the detailed technical specifications mentioned in boq sl no 110 of annexure xiv supplying and fixing following way single pole and neutral sheet steel mcb distribution board 240 v the detailed technical specifications mentioned in boq sl no 111 of annexure xiv supplying and fixing 5 a to 32 a rating the detailed technical specifications mentioned in boq sl no 112 of annexure xiv supplying and fixing metal box of following sizes nominal size on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc the detailed technical specifications mentioned in boq sl no 113 of annexure xiv providing and fixing decorative ceiling light...